Search results

6x284 VS Denial verdict GUILTY My rifle is a 30"bbl Rem 700 8" twist . I wanted and expected high velocities right out the gate. Instead my brass was actually ruined by to hot of loads . I made a rookie mistake and ignored case head expansion as a clue that my loads were to hot. I'm...

Seating depth Thanks Boyd Allen ,I will continue with Body die and I think I'll seat bullets another .005 deeper .

Just back from shooting Loaded 17 rounds . 7 rounds Berger 105 Hybrid Neck diameter with bullet .2715 Seating depth using Sinclair nut 3.311 to Bullet ogive Base after using Redding body die .4985 Case length 2.160 10 rounds Hornady 105 Amax Seating depth 3.326 to ogive all other...

Putting words in my post Where did I say I was the expert ? Those 4 things you mention are all presumptuous conjecture . Just got back from desert shooting today's loads. I'll post results during 49er-Bears half time .

No resistance when lifting the bolt . No abnormal resistance when lifting the bolt at all. But once bolt is fully cammed up? When I pull rearward it immediately resist( However after turning and additional .002 resistance was minimized ,surely that's a clue ?) . But why not when shooting the...

Cases have never been to long ! " That's elementary my dear Watson " Alinwa my brass is trimmed to 2.160 I've never had a chambering problem . Your the one that's jamming on. You also miss quot me. I shaved an additional .002 off,then the extraction resistance was minimized with berger...

What is minimum What is minimum neck wall thickness ? I'll get one of those mics at Cabelas .

Open my mind Guys I had a chamber cast done. Gunsmith( wasn't the one that chambered this bbl) said my neck was .276.( He was wrong) He didn't let me walk away with chamber cast ,just said it was .276. He said " turne necks down to .274" . I did and still had stiff extraction. NOT on lifting...

Ok I have purchased a Redding body die for 6/284 and that didn't help,I turned neck down until a fired case would easily accept a bullet. So just got back from firing 10 rounds. With 105gr Berger Hybrid turning necks down reduced case extraction problems,but didn't eliminate this problem a 100%...

6x284 Re#33 Hey that's what I shoot. I also have Re#33 what charge would you suggest I start with ? I have a 30" Brux 8"twist bbl

Can berger 105 Hybrids be pushed over 3200 fps ? I'm pushing them to 3400 FPS and they group nice at 100yds. Others say they usually blow up before they make 200 yds when pushed above 3200 ?

.276 Had a chamber cast done. Neck measures .276 so I'll be turning them to .273. Gunsmith said my chamber looks just fine,but signs of throat wear are plainly visible and says maybe another 1,000 rounds .

Thanks every one. I'm going to have a chamber casting done by different gunsmith,and he'll provide the bottom line on what to do. Former gunsmith didn't tell me what the neck dimensions were.

Neck is too tight Virgin case .498 Fired case .4995 sized case .499 Case neck absolutely will NOT accept a bullet. All my current guns and every one I've ever had would easily accept a bullet just as you described.

Do it my self ? Ok did a search on honing a chamber . A drill motor and product recommended oil ? I'll research this more thanks.

Redding small base body die Can some one provide a link to the specific measuring tool I need to purchase ? The neck isn't expanding in the neck area of chamber with or with out a bullet, its the same size before and after firing .2745. Ok worst case scenario is the fix having a gunsmith run...

Doughnut There doesn't appear to be a " Doughnut " in the case neck. The bevel on the berger bullet is even with the base of the neck.

Additional Neck turning Interesting, so additional neck turning might not fix the problem ? Could my gunsmith of used the wrong reamer ?He did tell me he prefers a tight chamber and to FL size my brass. What would be the fix ?

No I don't No I don't. Why would new brass same load not have an extraction problem and 2nd firing with same load does ? Also this is a Brux bbl 8"twist if that makes any difference.

Need another tool Digital caliper ,is all I have now. I 'll buy one of these .RCBS® Vernier Ball Micrometer at Cabela's Mail-in Rebate RCBS® Vernier Ball Micrometer Sale! $67.99