Search results

Bob Jones in AZ. HAs the hoods & lenses that you seek. bjonessights.com

Rubicon Prec- Negative-the handle will break before the handle comes off the bolt body. Not to mention the inclusions & voids in the cast OEM Rem handles- LOCATE & TIME the bolt handle correctly(w/o SCREWS or PINS) w/a properly TIMED trigger to sear "Hand-Off" & two fingers is sufficient to...

CMaier- Basically,YES. The TactiKool crowd crave the Louisville Slugger Baseball Bat Knob option,stating it is easier to manipulate the bolt w/ gloves on- B.S.-two fingers is all that's required to manipulate a bolt. Adding length/weight(arm/moment) to the bolt handle will induce more...

With out a shoulder for the Louisville Slugger Baseball Bat knob to butt up against the handle will break at the threads. Adding weight to the handle is the worst option.

TIG welding on a barrel will oxidize/scale the bore. Negative! A purge will eliminate any raised carbon.

There is a reason that one has to be certified to silver braze aircraft or submarine parts. Cadmium is your friend when it comes to silver brazing. Epoxy would have been your best bet.

Some believe wrapping a piece of plastic over a stock & drilling 2 holes to insert a couple carriage bolts/nuts to acquire an adjustable cheek piece is practical also. Bastardizing an action by enlarging or drilling & tapping a hole to insert a bolt or spring loaded bolt stop is...

muley, IF, you ever inlet/pillared/bedded/shouldered/shot a Robertson Composites stock you would purposely mutilate/cut-up any HS,McM &/or Manners stock to get the aforementioned stocks out of circulation.

OP, You'll loose your bolt release lever not the bolt stop pinned into the receiver. As Dusty mentioned,you have the option to depress the bolt stop w/a small pocket screwdriver to remove the bolt from the receiver. An Anschutz style bolt stop is popular on most of the Rem Custom Clones...

4Liberty- Try some Super Lube from the aerosol can. Sprays on like WD40 & tacks up thicker than white lithium grease. Color is translucent clear. Spray inside an AR upper, move around w/ a Q tip & let tack up. Spray the dis-assembled carrier/bolt & firing pin & re-assemble. 90% of carbon in...

HS stocks have a hollow cavity behind the butt pad similar to but smaller in size to the storage compartment in an AR-15/M16 butt stock. Warner Tool Co.thumb wheel adjustable cheek piece hardware is easily adaptable & has the option of cast on & cast off. The cheap TactiKool piece previously...

It's only temporary- The white stuff will be on the ground here in AK 'till official "BREAK-UP" the end of April middle of May. (break up is when the rivers start flowing house size ice chunks downstream) All dependent on Mother Nature 10's of thousands place bets/guesses on Break Up check...

D.Kiff/PT&G offered SAKO extractor cut .378" faced bolt bodies & extractors initially. The combo was short lived. A 700 S/A bolt will fit into your 722 action. The only difference is the anti bind slot cut in the RH bolt lug of the 700 bolt & of course the handle.

Part/Cut the Bbl off & re-crown it. Thread it & install a weed burner! OR Re-Barrel it

The Rem Custom Shop could tell you exactly what the rifle was chambered in & by which 'smith by the suffix lettered serial number. Bbl length of A 40XB will be 27 1/4" Bbl length of a 40XC will be 24" but in a repeater configuration. Yes, the rifle was proof tested & stamped<REP> on RH side of...

As previously mentioned A sawzall & paraffin wax as a lube. (paraffin won't contaminate your ingot pot or mix) Try cutting an 80+Lb plumbers ingot into quarters! Been there,done that .....just a couple months ago!

Equip configuration variables- Action underlugged/double underlugged? Action Pillared or Glue in? Barrel Manuf/Chamber/Twist? Bolt Manuf? Op Rod Manuf? Bolt Roller to Op Rod properly TIMED? Gas Cyl Manuf? Gas Cyl-Front Band unitized? Stock Front Band/Gas Cyl pre-loaded or not? Piston(s)...

Do you fusion weld the front of the sleeves under the lugs as well? Are you talking about gassing a purge chamber or upping the flow to help cool the weld? If your question is to fusion TIG weld the sleeves "under the lugs"-NO Depending on sleeve thickness-break fwd & aft ends after...

Nat, Need product for advanced testing !! I'll skip the tactikool knob part & just use two fingers as the required tools.

I've fusion TIG weld 1pc & 2pc sleeves on hundreds of customers bolt bodies over the years. Think.....PURGE !!!!!!! Sleeves were installed from the aft end of the bolt body, 'cause the handle's were removed to re-LOCATE & TIME for primary extraction. Less heat than soft soldering Guaranteed...