Search results

Yes & All 40X Models have chrome moly(blued) trigger groups,not stainless.

Simple- Purchase,have installed,have adjusted a Bix-n-Andy Competition trigger group. Place the Basix(JUNK) on an anvil & accelerate a 4Lb sledge hammer upon the trigger group to take it out of circulation.

OP, WHY would you need to un-rivet the side plates? IF,upon disassembly a burr is witnessed on the inside of either side plate-stone the burr away. Push the trigger lever pivot pin out of the housing from Rt to Lt. Disassemble a M.Walker 700 trigger group, a Shilen is a copy.

It was assembled at one time.....reverse the process.

OP, Since you needed to ask- You should have sought a professional from the get go,as your first attempt was pure luck.

gklitz, A 40X rimfire has a 722 straight/perpendicular bolt handle w/a round knob (aka 721/722). A 40XR rimfire has a swept bolt handle w/ knurled knob (aka 700). The 40X rimfire bolt has middle bolt lugs that lock up in the forward face of the rear bridge of the receiver. Bolt lugs are .375"...

OP, Your newly acquired 40X is a 40X rimfire or centerfire 40X? IF,the OEM barrel is installed on either rimfire or centerfire the task of fitting a bolt is elementary. IF,an aftermarket barrel is installed simple measurements will set the precedence. No my first Rodeo!! ACCU-TIG.com

rsmithsr, Asa is CORRECT. 20rd mags were used w/ 77 & 80gr loads staggered kitty corner in the mid to late 90's to run in NRA Nat'l & CMP EEIC Matches. Derek Martin-Accuracy Speaks- was the instigator if memory serves me correctly.

OP, Your "Old' style Rem trigger is a M.Walker design trigger group. Your RR prefix receiver had a X Mark/X Mark Pro trigger group. IF,your 'smith choice has questions.....seek elsewhere. No,the handle does NOT have to be removed to machine the bolt lock safety cut in the bolt body. But,your...

OP, IMR 4895 or IMR4320 burn rate powders are what you seek to reload for the 350 Remington Magnum.

OP, The next allen head cap or set screw that you have issues with- shock it prior to attempting to loosen it. A pin punch is inserted into the hex drive...& not a press fit...& tap the punch...loosens easily. If the hex drive is buggered up..take a larger than hex size punch to displace...

alinwa, Any Gold washing, wet or dry banking operation will have Black Sand & Garnet. (If a panner does NOT have the above in his/her pan, there isn't any Gold.....either) Any crusher operation will not.

Excavate Grizzly Bar Trommel Sluice Shaker Table Wash table 5 gal Buckets of Black Sand(heavy) Garnet GOLD !!!

Op, Since you missed it,first time around- Per your pics- You have post 2006 "SHORT CAM" bolt handles on said bolts, that are approximately.160" OUT of TIME radially. The clearance between the handle & rear receiver ring is only ONE part of the equation. The above is critical in that if the...

Though not manufactured currently, an RWHart handle once a radius was blended out w/ a #6 needle file is/was a perfect fit for a Remington. ( I bought all RWHart had in inventory) I never assume any handle will TIME correctly. Any TIG welder w/ experience(s) & not wasting argon should be capable.

OP, There is NOTHING correct on any LH Remington. (1/2"-13tpi RH firing pin shroud thread is bass-backwards for proper functionality) The handle as pictured is a "Short Cam' bolt handle (2006 to present) as I've coined them. Eienstein &/or Houdini are incapable of correctly TIMING said bolt...

Any Remington 2 lug bolt is TIMED into Battery & NOT for Primary Extraction. So, depending on handle vintage any Remington is .080" to .160" OUT of Primary Extraction TIMING. Moving/repositioning the handle forward/closer to the rear receiver ring, is only ONE part of the FIVE part equation...

Ben H, I have a dozen PT&G .378" .699" diameter OEM Rem extractor/ejector configuration bolt bodies on location. The original bolt w/ a simple clearance measurement would be required to duplicate a drop in replacement.

OP, As OliveOil stated..... You de-burred a burr from inside of the case neck into the case. Tumbling the cases would have removed it. Loading & firing the case...removed it.

A mills/vice A drill bit(undersized) A box cutter(router bit) 2 line levels Start inletting