S
shooter 70
Guest
thinking of ordering a eabco barrel for savage 110 in 260 cal anyone have one of these barrels or comments on them the advertise direct fit replacement is this true
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
C
caroby
Guest
Yes,
Have seen a .223 CM barrel from them that shoot good sub 1.00 groups typical... Coppered a tad, but fit and finish was as advertized.
cale
Have seen a .223 CM barrel from them that shoot good sub 1.00 groups typical... Coppered a tad, but fit and finish was as advertized.
cale
S
shooter 70
Guest
thanks for the info this will be first barrel install wanted to start simple
C
caroby
Guest
Think about LW
If you are wanting a >>>SHOOTER<<<.............. Go LW...
I have seen 4 Lothar pre chambered .223's ... 3 1-12" and a 1-8"...
I'm sure they can set ya up with a .260...
They shoot with any other custom tube..! They are CAPABLE!
Typically < 300.00 shipped...
http://www.lothar-walther.de/339.php
Just call Woody...
770-889-9998
Won't be dissapointed!
cale
thanks for the info this will be first barrel install wanted to start simple
If you are wanting a >>>SHOOTER<<<.............. Go LW...
I have seen 4 Lothar pre chambered .223's ... 3 1-12" and a 1-8"...
I'm sure they can set ya up with a .260...
They shoot with any other custom tube..! They are CAPABLE!
Typically < 300.00 shipped...
http://www.lothar-walther.de/339.php
Just call Woody...
770-889-9998
Won't be dissapointed!
cale
S
shooter 70
Guest
great link caroby are u a savage shooter if so any ideas on 110 action upgrades or is action ok for a 500yd weekend shooter
G
GaCop
Guest
EABCO Barrel
I just finished building a 260 using an EABCO barrel on a 110 action. It took about 60 rounds to get the barrel to settle in fouling wise. I'm still working on load development but have had a number of groups between .600"/.900" at 100 yards. I'm currently reforming RP 7mm/08 brass but plan to switch over to Lapua as soon as I can get a hold of some. Action is pillar bedded in a Duramax stock and action topped off with a Nikon 6X18X40 side parallax adjustment scope in Weaver 4X4 rings on an EGW mount.
Tom
I just finished building a 260 using an EABCO barrel on a 110 action. It took about 60 rounds to get the barrel to settle in fouling wise. I'm still working on load development but have had a number of groups between .600"/.900" at 100 yards. I'm currently reforming RP 7mm/08 brass but plan to switch over to Lapua as soon as I can get a hold of some. Action is pillar bedded in a Duramax stock and action topped off with a Nikon 6X18X40 side parallax adjustment scope in Weaver 4X4 rings on an EGW mount.
Tom
S
shooter 70
Guest
action
any action upgrades on 110 or is it factory
any action upgrades on 110 or is it factory
B
Bambob
Guest
Does anyone know for sure who makes barrels for EABCO? I've always thought it was probably "Green Mountain".
Bob
Bob
C
caroby
Guest
any action upgrades on 110 or is it factory
Sorry..... Been away from the Gunsmith forum.......
All but one has a "Full On" SSS work with a Evolution trigger... Very Nice!
In other words, the guns I have been around were totally factory Savages with LW barrels... Very capable.
Here for Sharp Shooters Supply:
www.sharpshootersupply.com
Here for more good Savage info:
www.savageshooters.com
cale
B
Bnhpr
Guest
I just finished building a 260 using an EABCO barrel on a 110 action. It took about 60 rounds to get the barrel to settle in fouling wise. I'm still working on load development but have had a number of groups between .600"/.900" at 100 yards. I'm currently reforming RP 7mm/08 brass but plan to switch over to Lapua as soon as I can get a hold of some. Action is pillar bedded in a Duramax stock and action topped off with a Nikon 6X18X40 side parallax adjustment scope in Weaver 4X4 rings on an EGW mount.
Tom
My suggestion is to get a gunsmith to put a krieger or Broughton, shilen etc bbl on it, and do away with the nut.
I put a 12 twist LV Krieger on a Savage a few months ago, and it went from 1.5" groups to shooting in the .200-.300 range....which I think it could do even better in better hands.
S
shooter 70
Guest
savage build
started this project as a rebarrel on an old rifle now im ordering shilen match barrel sharpshooter bolt and knob stockade custom stock and am trueing and polishing action.where does this insanity stop!!!!! i guess all i need to know now is how do i get into benchrest and are there any matchs in the alabama area.
started this project as a rebarrel on an old rifle now im ordering shilen match barrel sharpshooter bolt and knob stockade custom stock and am trueing and polishing action.where does this insanity stop!!!!! i guess all i need to know now is how do i get into benchrest and are there any matchs in the alabama area.
S
shooter 70
Guest
oh forgot about ordering shapshooter trigger 2