Search results

The disconnector catches the rear hook in the hammer after firing. upon release of the trigger lever in semi auto mode- the disconnector hands off the hammer to the sear surface cut into the fwd face of the trigger lever. Upon trigger take up prior to firing the disconnector does touch the...

OP, Roll the action up-side down & look thru the mag well for the 1/2 football shaped scallop cut in the rear bridge starting from the lug raceway towards center of bridge. .378" bolt face receivers do not have the scallop. .473" & .532" bolt face receivers have the scallop...or should. I've...

Joe, Your S/A- Look to see if there is a 1/2 football shaped scallop inside the rear bridge fwd o/b corner/aft o/b corner of ejection port. The .378" bolt face receivers do not have the scallop for case ejection clearance. Some S/A .473" bolt face receivers did not get the required machine work...

Alinwa, Be Well Be Safe Have FUN!! My Friend!!

OP, As Dave Tooley described & to add- I would suggest for a sporting rifle once the bolt nose is bushed/soldered/faced to bore the bushing I/D to .005" clearance per side or...ex.532"+.010"=.542" diameter. Take your bolt in hand Insert a piece of brass into breech face of bolt nose Push the...

Not in a 30BR I've loaded/shot quite a few of the Shooters World/Lovex powders in numerous calibers. Best point of sale is that it is NOT bottled by Hodgdon!!

indicated & cut perpendicular to bore axis,some cuts have more protection for their intended purpose. a .010" break/chamfer may prolong the cuts longevity. a q-tip after visual inspection will help ascertain if a burr is present. Accuracy wise,there's only one option- try each cut on the same...

OP, Pull the Bbl'd action out of the stock since it is inlet so deep to ascertain if any model designation is stamped in the receiver. Trigger lever w/ grooves(700) compared to smooth(722)lever & appears to have the 40X Repeater trigger group pull weight adjustment screw modification by the...

3/16" total pin fall? (someone's been hacking) Install another OEM striker/cocking piece & measure the outcome. Once you shorten the aft end of the pin & drill another cross pin hole you will have other issues to contend with since the striker/cocking piece will hit the bottom of the firing...

Early short shroud f/pin assy pictured. Measure total firing pin fall not striker to sear hand off.

sample measurements in bold type from unmolested Rem 700. Increasing travel by cock on close/striker to sear hand off is subtracted?

A dial indicator will eliminate all of ones misconceptions of striker to sear hand off.

Sell the TupperWare stock. (GLUCK needs more plastic since TupperWare & RubberMaid have imposed restrictions on cupboard utensil manufacturers) A B&C stock would be light years ahead of any OEM Rem tupperware stock.

A Remington pin fall is approximately 1/4" & is cock on open & cock on close....until it's corrected. Drilling a 3/32" cross pin hole & parting off the aft end of said firing pin is elementary to increase pin fall if/when striker to sear hand off is accomplished.....correctly.

Yep Another incompetent brain dead federal employee attempting to put a feather in his/her cap. Wait until the Feds tighten the nous restricting Hodgdon who now bottles most of our canister powders. Times will be tougher in the future w/o regard who's on Penn Ave. We will be back to sticks &...

OP, NOT good for a single company to be bottling several companies powder products for distribution in the USA.IMO. The anti's/elected crooks turn up the heat & these crazy times that we see today will be mundane by comparison for the shooting sports.

1st- Do not believe Hodgdon's marketing hype/BS. Each Bbl shoots/cleans differently. Load a couple rounds in 1gr increments shot through a quality chronograph will tell the tale.

A covert act from a competent organization to individually "CAP" all involved would be appropriate before the legalized crooks take it to their graves.

AA-Accurate Arms Powders was based in McEwen,TN. A-Accurate Powders of Western Powders is based in Montana. different Companies...like comparing- Dupont IMR Powders of Canada(steel can) IMR Powders bottled by Hodgdon(black plastic bottles)

Tim, There is no way in this so called "Free World" that you can fix stupidity,& some stay up nights studying to be more ignorant. A mandatory hunter safety/concealed carry course should be a prerequisite to any firearm purchase...for all ages.