Search results

Here are a few from T K Lee.............. Iron Sight, Inc. Attn: Mike Sexton 4814 S. Elwood Ave Tulsa, OK 74107 (918)445-2201 (918)521-7736 Redfield, Weaver, Unertl and others Osborn Optical Systems Atn: Earl Osborn 585 S. Dewey Road Dewey, AZ 86327 Phone & Fax (928) 632-8717 Most...

BREAKING NEWS President Obama has just confirmed that the DC earthquake occurred on a rare and obscure fault-line, apparently known as "Bush's Fault". He also announced that the Secret Service and Maxine Waters will be investigating the quake's suspicious ties to the Tea Party. Meanwhile...

in my thinking? I previously posted about a problem with factory loaded Hornady brass in 204 Ruger and contacted the factory. They acknowledged a manufacturing problem. I then told them that I would rather have an equivalent value of bullets rather than factory loaded ammunition. They sent me...

My 1730 Annie also has the 1 in 16 twist and is a bit finicky about bullet selection, so far best results with lighter bullets have come with the 30 grain Barnes Varmint Grenade and the 35 grain VMax. Berger 36 grains will keyhole for me. Lil Gun is my go to podwer also.

Just got a call from Hornady QC..........brass is out of spec. They offered me replacement ammo, but I settled on components.......VMax slugs. Told the tech I had already purchased WW brass.

PacNor replied to my email and stated that they function test with Winchester ammo, rifle was originally chambered in 223 Remington...nominal SAMMI rim thickness for 223 and 222 should be .041", and the 204 rim is @.045". I just checked function with a 221 Fireball brass and it worked ok also...

I was thinking along the same lines as you about rim thickness being the root cause of my problem. I talked with Hornady and they issued a call tag for the ammo so they could take a look at it.....also have an email out to PacNor to see what kind of brass they used for proof test. It's almost...

Just had a 204 Ruger chambered for a walking varmint rifle. I was breaking in the barrel and shot a box of Winchester factory ammo with no problems. I switched to Hornady factory and immediately had the following problem.........brass would extract but not eject, just layed in the action. At...

Freda Shaw who used to work for Unertl sent me this email a while back............... Good Morning, Herb, I finally have an address to send your Unertl Scope mount in for repairs by Unertl people: A. Davis - Unertl 1209 East Dayton Yellow Springs Road #251 Fairborn, Ohio...

Fred12 and moreplop are spamming

I'm just an old wood butcher, but I was fortunate enough to acquire an unused portable x-ray table originally designated for a MASH unit, then delegated to Civil Defense and then to me. The top was constructed of 1/4" Micarta which I incorporated in the top of both my reloading and casting...

ntx

Nemohunter is the correct name..................

The Colt Sauer used a system with 3 rear locking lugs that retracted into the bolt body, built hell for strong owned one in 25-06 and 375 H&H.

sounds like 9ring is in the camo business,3 posts to his name and all about the camo dip :o

54 has locking lugs at rear of bolt, 64 uses root of bolt handle as locking lug.

Go to the pet store, find some Zilla, which is ground walnut shells about the consistancy of sand. It's used for reptile litter and it's fine enough that it gets in everywhere, also cheaper than tumbling media.

The same.............but the comparison ends there)chill(

The short answer as to why Kimber 82G sights have 1/5 clicks is that they were manufactured in Australia and have metric threads.

I adjusted for inflation................