Search:

Type: Posts; User: Dave Tooley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    405

    Bases would be the same as a Remington front...

    Bases would be the same as a Remington front base. Spring, I believe a model7/XP100 will work. But verify that.
  2. Replies
    14
    Views
    1,222

    Al Pm sent your way

    Al

    Pm sent your way
  3. Replies
    32
    Views
    2,633

    AL, I'd use a spider instead of the 4 jaw....

    AL,
    I'd use a spider instead of the 4 jaw. Easier to adjust with the screws vs the chuck jaws.
  4. Replies
    32
    Views
    2,633

    Al, I've seen a custom built steady using a high...

    Al,
    I've seen a custom built steady using a high grade bearing instead of fingers with a spider built in. I seem to recall it was used for shotgun choke work. Made sense to me at the time. Would be...
  5. Replies
    27
    Views
    3,798

    I know Jef Fowler had over a million on his...

    I know Jef Fowler had over a million on his carbide 6MM dies. They were getting a bit fat and fish mouthed.
  6. Replies
    27
    Views
    3,798

    You can make a lot of bullets with steel dies. I...

    You can make a lot of bullets with steel dies. I started with a 6MM set Ferris made. To wear out carbide dies takes numbers around a million or more. Steel maybe a 100,000 but that's just a guess on...
  7. Replies
    16
    Views
    1,977

    Well duh

    A simple search on this site.

    https://www.accurateshooter.com/competition/new-scoring-reticle-approved-by-ibs/
  8. Replies
    16
    Views
    1,977

    No it wasn't. I sent all my measuring equipment...

    No it wasn't. I sent all my measuring equipment off and there was a card in the box with the reticle. He made a run a few years ago because of new clubs needing them.
  9. Replies
    16
    Views
    1,977

    I don't have his contact information but a...

    I don't have his contact information but a gentleman was making a scoring plate, all calibers, for the IBS. All you need is a 4X domed magnifier to go with it.
  10. Replies
    21
    Views
    3,157

    The majority of the time you get some taper from...

    The majority of the time you get some taper from work piece deflection.
  11. Replies
    27
    Views
    4,056

    It's called free machining for a reason.

    It's called free machining for a reason.
  12. Replies
    21
    Views
    3,157

    I know a little bit about what's being used....

    I know a little bit about what's being used. Most, if not all, are not capable of shooting the difference. Tier 1 groups have basically custom built rifles. They have smiths who take care of their...
  13. Replies
    11
    Views
    1,845

    Back when I was a garage smith with no heat I got...

    Back when I was a garage smith with no heat I got hung up in my spider which was doing 1250 RPM's at the time. I tore the sleeve out of a long john top and a sweater getting away from that thing....
  14. Replies
    11
    Views
    1,845

    50's are Sooooo much fun

    50's are Sooooo much fun
  15. Replies
    9
    Views
    2,946

    Every once in awhile you get one that sends you...

    Every once in awhile you get one that sends you to the psychologist. But but but it can't be me!
    I have several I have notes attached to reminding me about personality flaws they have.
  16. Wrap it in wax paper. Slow speed. May have to do...

    Wrap it in wax paper. Slow speed. May have to do it several times to get it to settle down. Just in case I keep precut paper by my machine.
  17. Replies
    19
    Views
    5,132

    25275 Rotary union is on a microphone stand....

    25275

    Rotary union is on a microphone stand. The manifold in the rear of the pic controls air as well as oil.
  18. Replies
    19
    Views
    5,132

    Many times I've forgotten to disconnect mine and...

    Many times I've forgotten to disconnect mine and run it through a couple of operations at 2,000 RPM's.
  19. Replies
    19
    Views
    5,132

    I have my rotary union mounted on a microphone...

    I have my rotary union mounted on a microphone stand with a 12" length of hydraulic hose.
  20. Replies
    9
    Views
    2,946

    I've never heard of Alpha Legacy. Carbide I get...

    I've never heard of Alpha Legacy. Carbide I get from JGS I run at 250-300 RPM's with flush oil. I have had reamers supplied by OEM's and they were ground for high HP machines and rigid fixturing....
  21. Replies
    2
    Views
    804

    I have to ask why do you need a small base die?

    I have to ask why do you need a small base die?
  22. Replies
    4
    Views
    1,432

    Funny When they said a bolt face was too hard to...

    Funny When they said a bolt face was too hard to bush. Enter the carbide endmill. Ezzzypezzzy
  23. Replies
    13
    Views
    2,373

    At one time I had Don's 22's,6's and 30's. I...

    At one time I had Don's 22's,6's and 30's. I think all of them were a 7 ogive.
  24. Replies
    2
    Views
    897

    Bolt thrust. Never worried about it. It's there....

    Bolt thrust. Never worried about it. It's there. Pressure in somewhat of a cylinder, regardless of shape, exerts equal force on all surfaces. Now we can discuss surface finish and lubrication on the...
  25. Replies
    1
    Views
    673

    Send Dave a print and tell him the changes you...

    Send Dave a print and tell him the changes you want. He'll make for you. I would go with a larger diameter neck.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4