Search:

Type: Posts; User: MilGunsmith; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    884

    Biathlon ammo

    Biathlon ammo
  2. I would think that for the purpose of indicating...

    I would think that for the purpose of indicating bores before chambering, the number value doesn't matter as long as there is no movement.
  3. Replies
    25
    Views
    3,859

    Everything you need to know about South Bend Lathes

    The SBL Workshop http://wswells.com/
  4. Replies
    21
    Views
    3,532

    Just remember that when doing a glue in, all the...

    Just remember that when doing a glue in, all the screw holes and other cavities that are normally filled with modeling clay during a regular bedding job to prevent lock in, will need to be addressed....
  5. Thread: rem 700

    by MilGunsmith
    Replies
    34
    Views
    5,241

    I think that this would only work well if you can...

    I think that this would only work well if you can keep everything clean. I also wonder how temperature sensitive the tight tolerances would be? If it's a hot day with a more rapid rate of fire and...
  6. Replies
    25
    Views
    3,859

    That will be to big, the tool holders will not be...

    That will be to big, the tool holders will not be able to get low enough to work. The ADA is the correct size.
  7. Replies
    15
    Views
    2,426

    I wonder if these states will still issue...

    I wonder if these states will still issue permits, Res and Non-Res, for those other states that require a permit to carry in their state? For example, a Utah Non-Res permit is good in over 30 states....
  8. Replies
    34
    Views
    6,475

    You can use your action truing fixture for short...

    You can use your action truing fixture for short barrels.
  9. Replies
    17
    Views
    2,733

    For rifle or pistol, the Champion or Knobloch...

    For rifle or pistol, the Champion or Knobloch adjustable frames are great. You can put the optical center directly in the center of your line of sight for each shooting position. You need to find an...
  10. Replies
    22
    Views
    3,118

    Can you supply some measurements of the diameter...

    Can you supply some measurements of the diameter and a close picture alongside a ruler?
  11. Replies
    34
    Views
    6,475

    If you clean up a parallel section over the...

    If you clean up a parallel section over the chamber in front of the tenon, you can run your steadyrest fingers there. An old trick with steel steadyrest fingers is to use a strip of fine emery cloth,...
  12. Replies
    4
    Views
    1,337

    I always try for the min HS .043" sometimes ends...

    I always try for the min HS .043" sometimes ends up at .044", need to allow for dirt. The SAAMI chamber headspace tolerance is .043" min to .051" max. The SAAMI ammo tolerance spec is .043"-.007"....
  13. Replies
    1,118
    Views
    674,973

    https://scontent-atl3-2.xx.fbcdn.net/v/t1.0-9/1492...

    https://scontent-atl3-2.xx.fbcdn.net/v/t1.0-9/149283800_3785577351529058_8856564215129783328_o.jpg?_nc_cat=1&ccb=3&_nc_sid=730e14&_nc_ohc=joLYmqNM-awAX_ha_J_&_nc_ht=scontent-atl3-2.xx&oh=66dad475981d6...
  14. That has been the standard for hi power matches...

    That has been the standard for hi power matches for years. One minute per round. The only time it is not enough time is when you have slow pit service, or your a bad shot with misses and crossfires...
  15. Replies
    8
    Views
    1,601

    If its the same style as a Remington, the hole is...

    If its the same style as a Remington, the hole is not critical just need clearance for the firing pin. it should only push on the shoulder.
  16. The AR Warner company makes one. Make sure that...

    The AR Warner company makes one. Make sure that you get the one that also uses grooving inserts. I use the positive rake cutters. Only about .125" wide and will cut upto a shoulder. Use plenty of...
  17. Replies
    39
    Views
    8,203

    Remember that next on their agenda will be...

    Remember that next on their agenda will be "sniper rifles", which they think of as a scoped accurate rifle. We all know what fits that description.
    Stand together, or fall separately.
  18. Replies
    9
    Views
    2,243

    Back when I was shooting smallbore 3P and 4P as a...

    Back when I was shooting smallbore 3P and 4P as a Junior, the Martini was one of the favored rifles.
  19. Replies
    4
    Views
    1,706

    Try it with an empty case first. The case will...

    Try it with an empty case first. The case will cushion the bolt upon closing and push it back to headspace on the lugs.
  20. Thread: Crowns

    by MilGunsmith
    Replies
    34
    Views
    9,942

    11 deg. Crown

    There is a theory that was tested that the 11 degree crown works best with the boat tail angle of the Matchking bullets. In all the sniper rifle barrel testing that we have done here, the 11* crown...
  21. Replies
    32
    Views
    7,760

    Back when I was shooting with the state National...

    Back when I was shooting with the state National Guard service rifle team, we played around at 600yards with our 40x .22lr rifles. When we were able to get hits on the 6' square target frame, but the...
  22. We have found in testing military ammo in a...

    We have found in testing military ammo in a Universal Receiver, that we need to have .030"-.039" firing pin protrusion and .020"-.025" firing pin indent in a SAAMI copper for 5.56mm small primer, and...
  23. Replies
    32
    Views
    7,559

    One club I was in tried a 20' hanging tunnel of...

    One club I was in tried a 20' hanging tunnel of old tires, with the muzzle in the opening. This worked well to deaden the blast, but not the sonic crack downrange. With most pistol, .22LR and other...
  24. Thread: Mirage

    by MilGunsmith
    Replies
    4
    Views
    1,661

    Highpower rifle shooters, who are not allowed to...

    Highpower rifle shooters, who are not allowed to use all the wind flags and pinwheels that are used in benchrest, usually keep the spotting scope focused on the mirage and use it to dope the wind...
  25. Replies
    29
    Views
    17,454

    Sticky: Bushing thought

    Has anyone tried making the bushing as part of the barrel chambering process? Turn and thread tenon for a close fit to a internal threaded bushing blank. Screw blank on to tenon, using 620 Loctite....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4