Search:

Type: Posts; User: rsmithsr; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    424

    the answer is, the correct way to do this is in...

    the answer is,
    the correct way to do this is in a lathe with the bbl dialed.
    high speed, very sharp tool cutting from the inside out
    a couple of thou deeper than the tallest land...if that...
  2. Replies
    25
    Views
    1,267

    he was still shooting earlier in the year. he...

    he was still shooting earlier in the year. he will be missed.
  3. Replies
    13
    Views
    405

    way too little info to base a reply on. yes i...

    way too little info to base a reply on.

    yes i have used .001 on a bolt gun
    but it was my gun my ammo and my loading process
  4. Replies
    21
    Views
    767

    willing to pay a known gunsmith to do work that...

    willing to pay a known gunsmith to do work that is better than mine.
  5. Replies
    21
    Views
    767

    davidson from brownells 3/4" drive flat steel...

    davidson from brownells
    3/4" drive flat steel bar

    om a side note....don't get snippy..i think you need to get better at the thread and shoulder. while i chamber ok, my local be 'smith is much...
  6. Replies
    21
    Views
    767

    i am lost why can't you tighten them ?? i use a...

    i am lost
    why can't you tighten them ??
    i use a bbl vice a rear entry wrench and a quality torque wrench.
    i been torqueing for over 50 years, schools and training just in torque.
  7. Thread: 40-x rebuild

    by rsmithsr
    Replies
    1
    Views
    753

    so.....long wait on a couple of items. i had the...

    so.....long wait on a couple of items. i had the bbl nitrited. took a while, and decide on a folding stock.
    none fit the bbl dia, so went with a mcmillian front half and an ar back with a quality...
  8. Replies
    21
    Views
    767

    golden bear in black brm-xd ?? i like...

    golden bear in black
    brm-xd ??
    i like torque...typically 125-150....
    but with the thread fit on the brmxd i felt very comfy at 125 with a 300 wsm
  9. Replies
    21
    Views
    767

    "deformed" thread on torqueing... can you prove...

    "deformed" thread on torqueing...
    can you prove it is the action and not the bbl ??/
    that is an actual question
  10. Replies
    13
    Views
    1,127

    IMHO your cases are too short. you would pick up...

    IMHO your cases are too short.
    you would pick up 20 thou by just going with 1.500
  11. Replies
    11
    Views
    922

    one should not drink "san miquel" and say they...

    one should not drink "san miquel" and say they were drinking beer
  12. Replies
    13
    Views
    1,127

    anything above the case shoulder/neck...

    anything above the case shoulder/neck junction..and still holds the bullet.
    i think my shortest is about .08
  13. Replies
    12
    Views
    1,278

    most have shelf life tho is is not always listed....

    most have shelf life tho is is not always listed.

    most stuff is temp sensitive

    pretty low humidity and used in a 78 degree facility
  14. well there is accuracy, and then there is...

    well there is accuracy, and then there is BENCHREST ACCURACY.
    no one suggested fmj, tho lapua makes a great 185 with a long history of long range performance.
    me thinks a 107 in a 12 lb rifle will...
  15. Replies
    12
    Views
    1,278

    WELL IT GOT HARD! my guess is the catalyst was...

    WELL IT GOT HARD!
    my guess is the catalyst was going bad and slowed down the expected process.
    time heals all...well mostly
  16. there are 2 DIFFERENT 107 match kings. early and...

    there are 2 DIFFERENT 107 match kings.
    early and current.
    they closed the tip for better bc on the new ones.
    heavy bullets for short range are seldom a good idea.
    is there a rifle weight limit ??...
  17. i do not think this is a good idea. if the 107's...

    i do not think this is a good idea.
    if the 107's are not the new factory design (new nose), i would pass.
  18. Replies
    1,176
    Views
    723,087

    my bet, it can do lots of things, dishwashing is...

    my bet, it can do lots of things, dishwashing is not high on the list
  19. Replies
    12
    Views
    1,278

    no. i have swicthed to marine tex, but had...

    no.
    i have swicthed to marine tex,
    but

    had steel bed left and used it for this job.
  20. Replies
    12
    Views
    1,278

    bedding not "hard"

    so i switched to marine tex, but had a bit of brownell's steel bed left.
    mixed up a batch and bedded a 40x single shot in a mcmillian stock and let it sit for
    20 hours at about 78*.
    popped it out...
  21. Replies
    11
    Views
    2,159

    yes today, trying to get a good screw, ends up...

    yes today, trying to get a good screw, ends up with us getting screwed
  22. Replies
    11
    Views
    922

    we apologize fir the current state of confusion,...

    we apologize fir the current state of confusion, and hope the USA you have come to know and trust will return....soon.
  23. Replies
    1,176
    Views
    723,087

    I was sitting at a long stoplight yesterday,...

    I was sitting at a long stoplight yesterday, minding my own business, patiently waiting for it to turn green even though there was no on-coming traffic. A carload of scruffy-bearded, young men...
  24. Replies
    1
    Views
    747

    yep i have used as little as 1 and as much as 3...

    yep
    i have used as little as 1 and as much as 3

    just another version of neck tension, but from the inside out.
  25. Replies
    27
    Views
    2,481

    plenty can tell you what .how to build a short...

    plenty can tell you what .how to build a short range 6ppc
    start with a light gun shoot in most classes...10.5 lbs
    bartlien. krieger bbl
    jewell trigger
    BAT action...DS most likely left port,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4