Search:

Type: Posts; User: martin zuck; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    966

    I was mistaken about the model with the wider...

    I was mistaken about the model with the wider varmint style forend, I believe it was a model R not G. As I said earlier the rotary magazine 250ís were 14Ē twist. As a general rule bullets over one...
  2. Replies
    18
    Views
    966

    Most of the old solid frame 250 99 rifles in nice...

    Most of the old solid frame 250 99 rifles in nice condition will shoot 3 shot groups in the 1 inch range if fed bullets under 100 grains. The ones with rotary magazines were 14Ē twist. I had a pair...
  3. Replies
    36
    Views
    7,371

    I talked to his right hand man last week and at...

    I talked to his right hand man last week and at that time I was told he was busy in the shop someplace. I guess he is still calling the shots.
  4. Replies
    36
    Views
    7,371

    Was reluctant to share my experiences with PTG as...

    Was reluctant to share my experiences with PTG as of late but maybe this will be a wake up call for them. I started dealing with Dave Kiff soon after after he left JGS. I know he knows better but...
  5. Thread: Kane

    by martin zuck
    Replies
    3
    Views
    1,867

    Thanks for the information. Martin

    Thanks for the information.

    Martin
  6. Thread: Kane

    by martin zuck
    Replies
    3
    Views
    1,867

    Kane

    Any one know the results of last weeks nbrsa Kane shoot?
  7. Replies
    195
    Views
    33,116

    Did not know Stan Buchtel was gone. Will miss...

    Did not know Stan Buchtel was gone. Will miss him.

    Martin Zuck
  8. Replies
    195
    Views
    33,116

    J

    J
  9. Replies
    33
    Views
    6,191

    A little bit of luck also helps!

    A little bit of luck also helps!
  10. Replies
    25
    Views
    5,299

    [QUOTE=martin zuck;844726]Believe me when I tell...

    [QUOTE=martin zuck;844726]Believe me when I tell you that the smaller I.D. spindle H10 will not accept 5C collets. Both machines need what you refer to as adapters. The 1 3/8 spindle for the 5C...
  11. Replies
    25
    Views
    5,299

    Believe me when I tell you that the smaller I.D....

    Believe me when I tell you that the smaller I.D. spindle H10 will not accept 5C collets. Both machines need what you refer to as adapters. The 1 3/8 spindle for the 5C collets and the South Bend...
  12. Replies
    25
    Views
    5,299

    The early H10ís were single tumbler while the...

    The early H10ís were single tumbler while the last ones were of double tumbler design. To my knowledge accept for length the beds were all the same. They also came with two different size spindles....
  13. Replies
    18
    Views
    4,831

    Also the 6br ack imp and a few more about that...

    Also the 6br ack imp and a few more about that size. They finally realized that at that range (1000 yds) bullet weight isnít near as important as BC.
  14. Replies
    5
    Views
    1,544

    Al, Pretty slick solution. Thanks for the input.

    Al,
    Pretty slick solution. Thanks for the input.
  15. Replies
    5
    Views
    1,544

    Thanks for the help. I will give them a try.

    Thanks for the help. I will give them a try.
  16. Replies
    5
    Views
    1,544

    Remington clone

    Need a little help. Am looking for a rem clone short action with 18tpi instead of 16tpi. Also with a bolt handle just like rem. If push comes to shove I suppose I could cut 16tpi over the 18 tpi that...
  17. Replies
    14
    Views
    2,732

    Maybe I didnít make myself clear. It would have...

    Maybe I didnít make myself clear. It would have made no difference the material of the rings. The unsupported aluminum section of front base with the ball joint action of the inserts made for the...
  18. Replies
    14
    Views
    2,732

    If you decide to use Burris insert rings and...

    If you decide to use Burris insert rings and youír base or front base extend over the front of youír receiver make sure to use steel. A while back I put a 375 Rem ultra mag to gather on a rem 700...
  19. Replies
    2
    Views
    1,061

    Check with Chad Dixson 3570 Mayer Avenue suit...

    Check with Chad Dixson 3570 Mayer Avenue suit B,Sturgis S.D. 57785. If he doesn't have one he might know who does. I have his ph. # but damned if I can find it.
  20. Replies
    5
    Views
    1,546

    If I remember right I don't think a ppc will...

    If I remember right I don't think a ppc will eject very well out of a panda with a .308 bolt face. With out an ejector the panda will work just fine. I think Jim Kelbly told me that. Any way I...
  21. Replies
    11
    Views
    6,157

    In years gone by we had cartridge called the...

    In years gone by we had cartridge called the 250-3000. Amazing how similar in performance it was and is to the new "creedmoor" cartridge. I guess my 250 rifles were ahead of their time.
  22. Thread: How manyii

    by martin zuck
    Replies
    5
    Views
    2,656

    Thanks for the help.

    Thanks for the help.
  23. Thread: How manyii

    by martin zuck
    Replies
    5
    Views
    2,656

    How manyii

    How many form dies are required to produce 219 Donaldson cases from 30-30 brass?
  24. Replies
    22
    Views
    15,057

    Pete, Most of these were taken apart and put...

    Pete,
    Most of these were taken apart and put back togather more times than they were ever shot. Iv'e rebarreled a few of them thru the years but they were solid frames. I don't know why you couldn't...
  25. Replies
    21
    Views
    11,321

    You hit thr nail right on the head! Back in the...

    You hit thr nail right on the head! Back in the early sixties after graduating from the Pennsylvania gunsmith school I went out and bought a brand new clausing atlas ten inch lathe. I could thread...
Results 1 to 25 of 382
Page 1 of 16 1 2 3 4