Search:

Type: Posts; User: blades; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: stuck barrel

    by blades
    Replies
    30
    Views
    2,529

    might try warming it up real good with a hair...

    might try warming it up real good with a hair dryer or similar. there might be some type of lock tight on the threads.
  2. Replies
    16
    Views
    1,831

    particulaerly since the new formulation. #9 was...

    particulaerly since the new formulation. #9 was the go to stuff for grenerations, for me the scent brings back many memories.
  3. Replies
    37
    Views
    5,069

    boy i remember both my sons sitting on my lap...

    boy i remember both my sons sitting on my lap pulling the loader handle for me as i was assembling match ammo for full course shoots as well as shotgun rounds.
  4. Thread: Pellet staging

    by blades
    Replies
    4
    Views
    977

    commercial pellets are swagged, not cast. Got to...

    commercial pellets are swagged, not cast. Got to be a nightmare trying to cast 8-14gr pellets with a hollow base. yes, there are solid base pellets but you need those to be dead on and dead soft for...
  5. Replies
    15
    Views
    3,927

    old material will sometimes turn out that way. it...

    old material will sometimes turn out that way. it might be quite awhile before it fully cures. there are mixes that get hard to a pliable state in about 4-8 hours but full cure will not be reached...
  6. Replies
    7
    Views
    1,737

    Butch in addition the stand alone compressors...

    Butch in addition the stand alone compressors there are booster units that run off air supplied by a standard compressor- not that they are any real saving dollar wise but less failure rate than the...
  7. Thread: Caldwell BR

    by blades
    Replies
    22
    Views
    4,965

    maybe the nut you got is not Acme ( not...

    maybe the nut you got is not Acme ( not typically found in hardware stores) then there is the possibility that, if it was ordered, it was picked wrong or packaged wrong. (or it is a 12 count...
  8. Replies
    1,288
    Views
    827,514

    not so crazy beats sweeping those pesky grass...

    not so crazy beats sweeping those pesky grass clipping
  9. Replies
    1,288
    Views
    827,514

    my question is , regaedig the extreme dude, if...

    my question is , regaedig the extreme dude, if unemployed -who the .... is paying for all this.
  10. Replies
    42
    Views
    10,862

    D's are single shot, I believe that the factory...

    D's are single shot, I believe that the factory sport class requires a magazine, D's & the Elusive E's do not have such.
  11. Replies
    18
    Views
    4,525

    What no clenched teeth , tongue twisted up,...

    What no clenched teeth , tongue twisted up, shaking hands and sweating forehead- geez all the fun's gone out this.
  12. Replies
    51
    Views
    17,163

    Pellets are almost pure lead- very soft. Easy...

    Pellets are almost pure lead- very soft. Easy enough to make a push through sizer out of a bit of tool steel. Course I have a small machine shop which gives a bit of an advantage in that department....
  13. Replies
    42
    Views
    10,862

    over my term here on earth I have seen a lot of...

    over my term here on earth I have seen a lot of various "factory " class rules. Same with "sporter" . The over all problem is how far one can bend / strech the rules.
    There are 2 types of 52c's...
  14. Replies
    2
    Views
    1,021

    had one for many years. Alas I drifted to the...

    had one for many years. Alas I drifted to the dark side, first co2 then pcp- mostly because of getting into benchrest at 25 meters and beyond. For its intended purpose it is as good as anything else...
  15. Replies
    3
    Views
    4,443

    that is an extremely rare occurrence....

    that is an extremely rare occurrence. congratulations.
  16. Replies
    13
    Views
    4,795

    mineral spirits another choice ( basicly Stodard...

    mineral spirits another choice ( basicly Stodard solvent - parts cleaner)
  17. Replies
    51
    Views
    17,163

    pellet seating tool- at one time marketed by...

    pellet seating tool- at one time marketed by Beeman. one end a bit pointed other a round ball, flared skirt out a bit or if deformed round it back out a bit.
    flat tray refered to was a sorting...
  18. Replies
    5
    Views
    1,318

    likely the best thing you can get would be the...

    likely the best thing you can get would be the daisy 753s - this is a single stroke/pump pneumatic rifle not a springer. Springers are notoriously difficult to shoot off a bench. Designed for 10...
  19. Replies
    27
    Views
    7,503

    at what distance? 50 Meters ? or 15 meters (...

    at what distance? 50 Meters ? or 15 meters ( 50ft) ? having played in both areas smallbore.
  20. Replies
    33
    Views
    11,063

    that same stuff is contained in hr 5717 ( I think...

    that same stuff is contained in hr 5717 ( I think that is the right #)
  21. Thread: alert HR5717

    by blades
    Replies
    2
    Views
    1,442

    alert HR5717

    Got this note from a friend House Bill HR5717- 50% duty fee on firearms and 30% on ammo, Plus you will need a fed lic. to purchase either. that's the gist of it. they trying to ram this through...
  22. Replies
    19
    Views
    6,884

    any add on unit yes, ported barrel no.

    any add on unit yes, ported barrel no.
  23. Replies
    19
    Views
    6,884

    terminology not a scrubber, ported extension of...

    terminology not a scrubber, ported extension of barrel , gas diverter, or ported barrel . An added on barrel extension would look something like the various muzzel flash/ recoil reduction units...
  24. Replies
    19
    Views
    6,884

    Now days you can break them off but not lite...

    Now days you can break them off but not lite them- I do not know if them make the strike any where type any more due to several lawsuits eons ago.
  25. Replies
    39
    Views
    10,923

    kinda like the credit card and biz loan sections...

    kinda like the credit card and biz loan sections of certain banking enterprises. That has been going on for a few years already.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4