Tab Content
  • TrxR's Avatar
    05-05-2021, 12:02 PM
    TrxR replied to a thread Redding 30BR dies? in General Discussion
    Thank Al I appreciate you measuring it for me. That will give about .001 - .0015" neck tension on brass turned to .010" But wont size enough...
    3 replies | 303 view(s)
  • TrxR's Avatar
    05-02-2021, 10:50 AM
    TrxR replied to a thread Shooting glasses? in General Discussion
    That's a good suggestion but I very much doubt I will find an optometrist around here that knows anything about shooting.
    17 replies | 1024 view(s)
  • TrxR's Avatar
    05-01-2021, 01:57 PM
    TrxR replied to a thread Shooting glasses? in General Discussion
    Im taking a serious look at the Pillas or Ranger Edge. I see Re Ranger states they use Zeiss lenses as well.
    17 replies | 1024 view(s)
  • TrxR's Avatar
    04-30-2021, 07:23 PM
    TrxR replied to a thread Shooting glasses? in General Discussion
    Im currently not needing prescription . From what i understand the Ranger edge frames do have an adjustable bridge to adjust the lense height.
    17 replies | 1024 view(s)
  • TrxR's Avatar
    04-30-2021, 12:53 PM
    Im curious as well.
    12 replies | 929 view(s)
  • TrxR's Avatar
    04-30-2021, 10:18 AM
    TrxR replied to a thread Shooting glasses? in General Discussion
    Which ones do you use? Ive looked at them and they are pricey. Ive also heard of fogging issues with the one pieces lenses where they tend to...
    17 replies | 1024 view(s)
  • TrxR's Avatar
    04-24-2021, 07:23 PM
    TrxR replied to a thread Lathe in Gunsmiths Corner
    It dont look like they offer the 1440tv anymore or i cant find it on their site. Did you get the vfd through Precission Matthews as well?
    24 replies | 2192 view(s)
  • TrxR's Avatar
    04-24-2021, 02:47 PM
    TrxR replied to a thread Lathe in Gunsmiths Corner
    So your using the vfd as a phase converter as well?
    24 replies | 2192 view(s)
  • TrxR's Avatar
    04-24-2021, 01:00 PM
    TrxR replied to a thread Lathe in Gunsmiths Corner
    Any truth to 3 phase lathes doing a better job than single phase? No 3 phase available here but could do some sort of phase convertor if there is a...
    24 replies | 2192 view(s)
  • TrxR's Avatar
    04-20-2021, 03:02 PM
    Thanks i believe im getting the plastic cases as well. And thanks for the tip about leaving the jaws open a little, ive already been doing that but...
    23 replies | 2807 view(s)
  • TrxR's Avatar
    04-14-2021, 08:49 PM
    Im hoping these will serve me well. They are both digital come with a hardwood case and the mic has carbide faces. Ive seen nothing but good...
    23 replies | 2807 view(s)
  • TrxR's Avatar
    04-14-2021, 02:27 PM
    I guess i dont. I was over thinking this. I just ordered a new mic and caliper set as my cheap calibers were dying anyways . Its got a Mitutoyo...
    23 replies | 2807 view(s)
  • TrxR's Avatar
    04-13-2021, 05:21 PM
    Would either of these be any good ? ...
    23 replies | 2807 view(s)
  • TrxR's Avatar
    04-13-2021, 11:49 AM
    Ive got a Mitutoyo 193-210 0-1" .001" mic which i dont think will work. Im assuming i need one to read in .0001"
    23 replies | 2807 view(s)
  • TrxR's Avatar
    04-13-2021, 09:39 AM
    Dont think thats quite what im looking for unless im searching the wrong thing. This is what im looking for but am not sure what model number it...
    23 replies | 2807 view(s)
No More Results
About TrxR

Basic Information

Statistics


Total Posts
Total Posts
310
Posts Per Day
0.07
General Information
Last Activity
05-07-2021 09:19 PM
Join Date
03-26-2009