Results 1 to 9 of 9

Thread: Farley Rest Rocking

  1. #1
    Join Date
    Jan 2013
    Location
    Georgetown, TX
    Posts
    198

    Farley Rest Rocking

    HEEELLLPPP!!!

    I just disassembled and cleaned/lubed my Farley Coax II rest. I used moly grease on all the surfaces I could get to and it operates smoothly and well in the vertical mode, but in the horizontal mode the bag holder "rocks" left/right; I don't recall it doing that before. It also moves easily up/down, but takes a lot more effort left/right.

    I'm lost; I don't understand where the left/right rocking is coming from. Do I have too much, or not enough, grease? Is there a way to remove the bearing plate/handle? It seems as though the bearing is loose in the plate, but I don't see any play; it's just the plate that seems to be rotating when I move the handle left/right. It also looks like the round rods are loose between the two plates, allowing the rotation.

    Any ideas? Thanks in advance!

    Dennis

  2. #2
    Join Date
    Sep 2006
    Posts
    760

    Check the allen keys

    With the bag removed from the top of the rest check to see if the two allen keys that attach the top to the rest are tight. Mine did the same thing and I hadn't taken it down to clean or grease it.
    Andy.

  3. #3
    Join Date
    Jan 2013
    Location
    Georgetown, TX
    Posts
    198
    Andy,

    Thanks for the reply. The top is tight; the plate that it's attached to is doing the rocking or twisting. It's about 1/4" movement or rotation.

    Dennis

  4. #4
    Join Date
    May 2006
    Location
    Hubert, NC
    Posts
    478
    There is a plate on the underside of the rest mid section that engages a slot on the rear movable plate and prevents the top from rocking left to right. If this plate is not firmly engaged in the slot, the top will rock. Loosen the 2 screws, press the plate firmly into the slot, and re tighten the screws. You may need to remove the top and mid section from the post, or at least move it as high as it will go with the height adjustment knob to see everything.

    Let us know if this helps.

    Scott

  5. #5
    Join Date
    Dec 2007
    Location
    Brisbane, Australia
    Posts
    2,305
    Scott,

    That's exactly what happened to a friend of mine.

    John

  6. #6
    Join Date
    Jan 2013
    Location
    Georgetown, TX
    Posts
    198
    Scott,

    I'll give that a try. Thanks!

    Dennis

  7. #7
    Join Date
    Mar 2005
    Location
    A pleasant place, Missouri
    Posts
    571

    Greases

    If the moly does not work out for you look into www.finishlineusa.com Look under greases.
    Centerfire

  8. #8
    Join Date
    Jan 2013
    Location
    Georgetown, TX
    Posts
    198

    Too Much Grease

    Thanks to all! I think I fixed it - I had used WAY TOO MUCH grease! I cleaned out the moly grease and lightly sprayed all sliding surfaces with some dry bike lube with Teflon. Everything's working smoothly and I don't notice the rocking/twisting any more. Only have to adjust the tension nuts and I'm done!

    Thanks again to all!

    Dennis

  9. #9
    Join Date
    Jan 2013
    Location
    Georgetown, TX
    Posts
    198

    Update

    Thanks again to all who helped with this. I thought I had it fixed, but no. I e-mailed Farley and got an over-night reply from Mike. He sent the following instructions:

    Roll Head unit all the way up on the vertical rack.(not off)

    Take and loosen (not off) bottom slider plate screws.(2 small button head allen screws under head unit)

    Remove large Jam nuts on spring plungers (leave spring plungers in)

    Loosen spring plungers 2-3 turns

    Slide joystick on and rotate assembly (will feel jerky and sloppy)

    Remove handle and tighten spring plungers (fully engaged)

    Fully tighten bottom slider plate screws.

    Go back and loosen spring plungers 1-1.5 turns

    Slide joystick on shaft (adjust tension to liking.)

    Apparently the order of assembly/re-assembly is important! Following these instructions, I believe I've actually got it this time!!

    Dennis

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •