Search:

Type: Posts; User: quandary; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    13
    Views
    11,211

    I use a bore scope. There's no other way, that I...

    I use a bore scope. There's no other way, that I know of, to see how much carbon is in the bore.
  2. Replies
    4
    Views
    3,886

    I use one and like it very much. It really...

    I use one and like it very much. It really teaches you to be consistent. After a while you kind of get a feel for it and you can tell if something is off without looking at the dial indicator. As a...
  3. Replies
    2
    Views
    1,743

    I tried it, lot# 4773, 29.5 grains, sloooowwww...

    I tried it, lot# 4773, 29.5 grains, sloooowwww pore through a loooonnnng drop tube, and got 3570 FPS average velocity with SD of 10, no pressure signs. Please beware of loads tried in rifles other...
  4. Thread: bore mop?

    by quandary
    Replies
    6
    Views
    1,746

    I tried using a bore mop but I couldn't get the...

    I tried using a bore mop but I couldn't get the chamber clean and dry enough to suit me. I bought some nylon bore brushes, a .416 Rigby I think (for my 30 BR) and wrap a patch for a .45 ACP around...
  5. Replies
    11
    Views
    2,937

    What do you use for lubricant in your rest top?

    What do you use for lubricant in your rest top?
  6. Replies
    27
    Views
    8,392

    I have to go along with Al on this. I use a...

    I have to go along with Al on this. I use a Harrel press. It works great for resizing cases, but I didn't get the most consistent results using it as a bullet seater though. For that I bought an...
  7. I tried C4 and it didn't do anything. I also have...

    I tried C4 and it didn't do anything. I also have a bore scope. What's your procedure?
  8. Replies
    0
    Views
    1,408

    New Edgewood front bag

    Edgewood has a new front bag with what they call a reinforced top. It looks and feels as though it's a piece of leather about 3/16" thick under the Cordura that runs the width of the bag, but does...
  9. Replies
    57
    Views
    20,859

    I know, I bought the requisite guide and couldn't...

    I know, I bought the requisite guide and couldn't get repeatable results.
  10. Replies
    57
    Views
    20,859

    I bought the Sinclair and got excellent,...

    I bought the Sinclair and got excellent, repeatable, results with Stiller and Panda actions, but I couldn't get it to work in an AR, no matter what I did. The Stony Point gauge works fine in the AR....
  11. Replies
    10
    Views
    3,206

    I shoot a 30 BR and buy my brass from Ron Hoehn....

    I shoot a 30 BR and buy my brass from Ron Hoehn. It's first rate stuff. He makes it in two neck thicknesses, .0094" and .0097", just tell him what you want. http://www.benchrest.com/hoehn/
  12. Replies
    5
    Views
    2,108

    I finally had a chance to try this today. The...

    I finally had a chance to try this today. The jump is much less, so I spent some more time dry firing and found a technique that eliminates the problem completely. Thank you for your suggestion. When...
  13. Replies
    5
    Views
    2,108

    Yes, Ratigan, If I understand him correctly says...

    Yes, Ratigan, If I understand him correctly says the buttstock shouldn't be bottomed, and Boyer says it should. I've tried squeezing the ears and not, to see if it made a difference. I can't seem to...
  14. Replies
    5
    Views
    2,108

    Trigger control

    Picture a benchrest score target. While carefully aiming at the dot, I pull the trigger (dry firing) and the dot in my scope jumps from the dot on the target to the ten ring at the right. This, even...
  15. Replies
    30
    Views
    8,902

    I tried it in an AR-15 shooting 52 grain bullets,...

    I tried it in an AR-15 shooting 52 grain bullets, 14 twist, 28" Hart barrel and I ran out of room in the case. Too slow. With a heavier bullet it might work though.
  16. Replies
    0
    Views
    1,247

    Ted Gundy, sniper

    http://www.youtube.com/watch?v=MQRpAxGVg4M

    I guess there some things you just don't forget. If I live to be 84, I hope I can remember my own name.
  17. Replies
    21
    Views
    9,648

    I use a Laserlyte, I got it from Midway, IRRC. I...

    I use a Laserlyte, I got it from Midway, IRRC. I have a space in my shop that allows me to check it at 75' which will get you on the paper. I don't remember how far off it was at 100 yards, but it...
  18. Replies
    5
    Views
    2,936

    Found it, thanks. I was searching on the old...

    Found it, thanks. I was searching on the old forum. Duh!
  19. Replies
    5
    Views
    2,936

    I searched that forum under "blue box lapua...

    I searched that forum under "blue box lapua brass", "lapua brass", "blue box", and "Roger T" and got nothing. The search engine is useless. It keeps telling me the search terms are too long or too...
  20. Replies
    5
    Views
    2,936

    Could you give us a hint at which thread it might...

    Could you give us a hint at which thread it might be, I haven't been able to find it.
  21. Thread: Imr 8208

    by quandary
    Replies
    8
    Views
    4,368

    I tried it on a .223 with 52 grain bullets (14...

    I tried it on a .223 with 52 grain bullets (14 twist, 28" barrel) and couldn't get it to work either, too slow. What bullets were you shooting?
  22. Replies
    12
    Views
    5,142

    I'll look around for one. Most of the timers I...

    I'll look around for one. Most of the timers I saw aren't rated at high enough wattage. What temperature do you go to, 650 deg F is the number i see most often?
  23. Replies
    12
    Views
    5,142

    Which darkroom timer do you use? This sure looks...

    Which darkroom timer do you use? This sure looks like the easiest and cleanest way to anneal cases. Do you quench your cases after heating them?
  24. Replies
    36
    Views
    10,826

    Very interesting, thank you very much.

    Very interesting, thank you very much.
  25. Replies
    36
    Views
    10,826

    I have some questions about setting up the barrel...

    I have some questions about setting up the barrel in your CNC lathe. It looks as though you're holding it in a 16C collet, and if you have a flat spindle nose I can see how you'd get the radial...
Results 1 to 25 of 49
Page 1 of 2 1 2