Search:

Type: Posts; User: Wayne Shaw; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.99 seconds.

  1. Replies
    15
    Views
    1,129

    I just found a one pound can like that I had N135...

    I just found a one pound can like that I had N135 in. Nasty brown crud coming out if the top.
  2. Replies
    5
    Views
    677

    It has been done before with no issues I'm aware...

    It has been done before with no issues I'm aware of.
  3. Replies
    7
    Views
    1,193

    Look on the rear edge of the action. They are...

    Look on the rear edge of the action. They are small, but should be there.
  4. Replies
    27
    Views
    2,564

    I'm going to assume he means making sure there is...

    I'm going to assume he means making sure there is no "inside corner/radius" at the tenon/shoulder junction. Then again, I could be entirely wrong.
  5. Replies
    4
    Views
    752

    I didn't find it.

    I didn't find it.
  6. Thread: Weikert

    by Wayne Shaw
    Replies
    2
    Views
    1,016

    Weikert

    Any results for Union County?
  7. Replies
    29
    Views
    5,779

    Jackie, did that create any cock on close?

    Jackie, did that create any cock on close?
  8. Replies
    9
    Views
    1,741

    I don't need glasses to read, thank you very much!

    I don't need glasses to read, thank you very much!
  9. Replies
    9
    Views
    1,741

    I can't read it, and I can't zoom in enough and...

    I can't read it, and I can't zoom in enough and it be readable.
  10. Replies
    39
    Views
    6,452

    Very sad news. Prayers for the family.

    Very sad news. Prayers for the family.
  11. Replies
    4
    Views
    1,142

    This year isn't turning out well for benchresters.

    This year isn't turning out well for benchresters.
  12. Replies
    24
    Views
    3,306

    Great post Kent.

    Great post Kent.
  13. Replies
    24
    Views
    3,306

    Very sad news. Such a great guy. RIP.

    Very sad news. Such a great guy. RIP.
  14. Sad news Russell. Keith was a good man.

    Sad news Russell. Keith was a good man.
  15. Replies
    18
    Views
    2,391

    Greg, I agree 100%. When I started using them, I...

    Greg, I agree 100%. When I started using them, I cussed like crazy. Then Jackie made a post and said "use a dab of grease on both sides to hold the wires...". No more cussing.

    And they are a...
  16. Replies
    18
    Views
    2,391

    1.071" over .032" wires.

    1.071" over .032" wires.
  17. Replies
    18
    Views
    2,391

    1.115" tenon and headspace.

    1.115" tenon and headspace.
  18. Replies
    19
    Views
    2,530

    Could be, but nothing else is on it.

    Could be, but nothing else is on it.
  19. Replies
    19
    Views
    2,530

    I need to edit this. My non-Culver measure does...

    I need to edit this. My non-Culver measure does have a stamp on the knob, It's CUSTOM PRODUCTS. I will try for some pics Monday.
  20. Replies
    19
    Views
    2,530

    I have a Culver, which has his name stamped on...

    I have a Culver, which has his name stamped on the perimeter of the end of the adjustment knob. I also have a "clone" that is made just about exactly the same, but no name stamp. I can't tell the...
  21. Replies
    12
    Views
    2,159

    Sad news. Bill was a great guy and always a...

    Sad news. Bill was a great guy and always a gentleman.
  22. Aint that the truth! Seems to be quite a few...

    Aint that the truth! Seems to be quite a few variants, but it should be simple.
  23. Now that's funny right there.

    Now that's funny right there.
  24. I fire formed a bunch of 257 AI brass. Most were...

    I fire formed a bunch of 257 AI brass. Most were OK, but there was thin brass where the bolt closed easy, and then some thick brass where I had a lot of effort to close the bolt. Don't recall the...
  25. An AI go gauge is normally .004" shorter than the...

    An AI go gauge is normally .004" shorter than the parent case go gauge at the neck/shoulder junction. This .004" is supposed to create a crush on the parent brass so it stays put when it is fire...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4