Search:

Type: Posts; User: Mram10; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.38 seconds.

  1. Replies
    15
    Views
    412

    I appreciate the extra info but of the two, which...

    I appreciate the extra info but of the two, which would you choose and why? I have Lapua brass for my 6br stuff but I like Norma brass too.
  2. Replies
    15
    Views
    412

    6 dasher or 6 dasher Norma?

    Deciding on next build. Which is your preference and why? Thanks
  3. Thread: Bedding bases

    by Mram10
    Replies
    17
    Views
    586

    Why not epoxy them to the action? Do many people...

    Why not epoxy them to the action? Do many people remove the bases often?
  4. Replies
    5
    Views
    581

    There are many flights with less than 10 people....

    There are many flights with less than 10 people. Huge loses. Had one with only a family of 4 last night and a couple today with 2 and 3 people on 737s that seat 143 to 175 depending on the model....
  5. Replies
    6
    Views
    556

    Here are the 6br on the left and my 6.5 hybrid on...

    Here are the 6br on the left and my 6.5 hybrid on the right
  6. Replies
    23
    Views
    1,516

    Iím curious about bedding then lapping after,...

    Iím curious about bedding then lapping after, what the difference might be. It is a low torque system so 8k psi epoxy should be enough in the gaps.
  7. Replies
    9
    Views
    810

    Get on multiple sites. Longrangehunting,...

    Get on multiple sites. Longrangehunting, accurateshooter and here can answer most questions. What is your goal? BR? LR steel? PRS? Most of your questions have been answered with google. If youíre...
  8. Replies
    6
    Views
    556

    Interesting. Post your results

    Interesting. Post your results
  9. Replies
    6
    Views
    556

    Iíll shoot whatever is the most accurate. Nothing...

    Iíll shoot whatever is the most accurate. Nothing set. Thx
  10. Replies
    6
    Views
    556

    6.5 dasher load data?

    Iíve been toying with a 6mm br, necked up to 6.5 and blew the shoulder and body out a bit. Point is, does anyone have an Load info for this type of cartridge? Tried 130otm with 28g Varget to fully...
  11. Thread: Pillars

    by Mram10
    Replies
    21
    Views
    3,413

    Well said. Iíve always made mine fairly tight...

    Well said. Iíve always made mine fairly tight fitting and it definitely scrapes off some epoxy. Iíll leave more slop next time.
  12. Thread: Pillars

    by Mram10
    Replies
    21
    Views
    3,413

    Is there an advantage to threading the outside v...

    Is there an advantage to threading the outside v the channels? I make mine like yours, but have seen others use threaded pillars successfully
  13. Replies
    19
    Views
    2,992

    Thanks. No idea where Iíd find that issue but...

    Thanks. No idea where Iíd find that issue but Iíll google it
  14. Replies
    19
    Views
    2,992

    Thank you. Iíll check it out

    Thank you. Iíll check it out
  15. Replies
    19
    Views
    2,992

    Thanks. Will do

    Thanks. Will do
  16. Replies
    19
    Views
    2,992

    I watched that before, thanks. Was looking for a...

    I watched that before, thanks. Was looking for a tutorial. I found one write up without pictures.
  17. Replies
    19
    Views
    2,992

    Thank you. I was considering a sleeve and use the...

    Thank you. I was considering a sleeve and use the oem firing pin. Your way sounds easier
  18. Replies
    19
    Views
    2,992

    Bushing firing pin?

    How important is it on the accuracy scale? Is there a good write up on how to do it? Is it worth it? Thanks
  19. Replies
    75
    Views
    9,506

    I apologize for the snowflakes that have been...

    I apologize for the snowflakes that have been offended over an honest question. Donít know a thing about your rifle, but best of luck in your search. There are a few good guys on here that are very...
  20. Replies
    56
    Views
    6,217

    Just when I thought you were being nice and...

    Just when I thought you were being nice and answering the question...
    I havenít signed of PM. Just donít go there much since my lathe and mill are setup.
    Signed off AS because they had an issue...
  21. Replies
    56
    Views
    6,217

    I didnít see your advice. Thank you. Didnít know...

    I didnít see your advice. Thank you. Didnít know wire would be easier. Watched wheeler do some but didnít know to look for blackening of flux. Again, thanks
  22. Replies
    56
    Views
    6,217

    This thread is done thanks to some trashy type....

    This thread is done thanks to some trashy type. Appreciate the pointers that were given. I just need some ribbon silver to braze on.
  23. Replies
    56
    Views
    6,217

    What am I doing? Seems youíve got a handle on how...

    What am I doing? Seems youíve got a handle on how this all started.
  24. Replies
    56
    Views
    6,217

    Agreed.

    Agreed.
  25. Replies
    56
    Views
    6,217

    Dave, sure seemed like Iím the one in discussion....

    Dave, sure seemed like Iím the one in discussion. If that wasnít your intent, I apologize.

    Louis, dan40, you guys have been on ignore for a long time. Feel free to waste other peopleís time....
Results 1 to 25 of 438
Page 1 of 18 1 2 3 4