Search:

Type: Posts; User: Dave Tooley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    1,548

    Back around 2000 Jammie Cass was running steel...

    Back around 2000 Jammie Cass was running steel heads at Hawks Ridge. Bullets wouldn't stay together on a consistent basis. I'm sure some of the Williamsport crowd tried before that.
    Sigs ingenuity...
  2. Replies
    14
    Views
    524

    Jeff Summers gets into the HOF

    Congratulations to my best friend of 40 years. He FINALLY got his 10th point today at the IBS Nationals.
  3. Replies
    3
    Views
    489

    In real world terms it's 1.728 from the end of...

    In real world terms it's 1.728 from the end of the neck. Add more for shorter brass.
  4. Replies
    34
    Views
    1,204

    Al You do have a way with words.

    Al
    You do have a way with words.
  5. Replies
    7
    Views
    662

    I'm familiar with several bullet manufactures and...

    I'm familiar with several bullet manufactures and only one runs multiple presses for the same bullet. Think Gov contracts. They may or may not mix bullets from different presses. I doubt it as that...
  6. Replies
    22
    Views
    1,197

    Move the handle forward, rotate CCW as need,...

    Move the handle forward, rotate CCW as need, adjust the end of the tang to align the anti bind rail. It's simple when you've 1000's of them. I have a fixture to do all that. I still send them to Dan.
  7. Replies
    1
    Views
    670

    Bases would be the same as a Remington front...

    Bases would be the same as a Remington front base. Spring, I believe a model7/XP100 will work. But verify that.
  8. Replies
    14
    Views
    1,680

    Al Pm sent your way

    Al

    Pm sent your way
  9. Replies
    32
    Views
    3,316

    AL, I'd use a spider instead of the 4 jaw....

    AL,
    I'd use a spider instead of the 4 jaw. Easier to adjust with the screws vs the chuck jaws.
  10. Replies
    32
    Views
    3,316

    Al, I've seen a custom built steady using a high...

    Al,
    I've seen a custom built steady using a high grade bearing instead of fingers with a spider built in. I seem to recall it was used for shotgun choke work. Made sense to me at the time. Would be...
  11. Replies
    27
    Views
    4,525

    I know Jef Fowler had over a million on his...

    I know Jef Fowler had over a million on his carbide 6MM dies. They were getting a bit fat and fish mouthed.
  12. Replies
    27
    Views
    4,525

    You can make a lot of bullets with steel dies. I...

    You can make a lot of bullets with steel dies. I started with a 6MM set Ferris made. To wear out carbide dies takes numbers around a million or more. Steel maybe a 100,000 but that's just a guess on...
  13. Replies
    16
    Views
    2,509

    Well duh

    A simple search on this site.

    https://www.accurateshooter.com/competition/new-scoring-reticle-approved-by-ibs/
  14. Replies
    16
    Views
    2,509

    No it wasn't. I sent all my measuring equipment...

    No it wasn't. I sent all my measuring equipment off and there was a card in the box with the reticle. He made a run a few years ago because of new clubs needing them.
  15. Replies
    16
    Views
    2,509

    I don't have his contact information but a...

    I don't have his contact information but a gentleman was making a scoring plate, all calibers, for the IBS. All you need is a 4X domed magnifier to go with it.
  16. Replies
    21
    Views
    3,703

    The majority of the time you get some taper from...

    The majority of the time you get some taper from work piece deflection.
  17. Replies
    27
    Views
    4,707

    It's called free machining for a reason.

    It's called free machining for a reason.
  18. Replies
    21
    Views
    3,703

    I know a little bit about what's being used....

    I know a little bit about what's being used. Most, if not all, are not capable of shooting the difference. Tier 1 groups have basically custom built rifles. They have smiths who take care of their...
  19. Replies
    11
    Views
    2,107

    Back when I was a garage smith with no heat I got...

    Back when I was a garage smith with no heat I got hung up in my spider which was doing 1250 RPM's at the time. I tore the sleeve out of a long john top and a sweater getting away from that thing....
  20. Replies
    11
    Views
    2,107

    50's are Sooooo much fun

    50's are Sooooo much fun
  21. Replies
    9
    Views
    3,147

    Every once in awhile you get one that sends you...

    Every once in awhile you get one that sends you to the psychologist. But but but it can't be me!
    I have several I have notes attached to reminding me about personality flaws they have.
  22. Wrap it in wax paper. Slow speed. May have to do...

    Wrap it in wax paper. Slow speed. May have to do it several times to get it to settle down. Just in case I keep precut paper by my machine.
  23. Replies
    19
    Views
    5,528

    25275 Rotary union is on a microphone stand....

    25275

    Rotary union is on a microphone stand. The manifold in the rear of the pic controls air as well as oil.
  24. Replies
    19
    Views
    5,528

    Many times I've forgotten to disconnect mine and...

    Many times I've forgotten to disconnect mine and run it through a couple of operations at 2,000 RPM's.
  25. Replies
    19
    Views
    5,528

    I have my rotary union mounted on a microphone...

    I have my rotary union mounted on a microphone stand with a 12" length of hydraulic hose.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4