Search:

Type: Posts; User: jackie schmidt; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.46 seconds; generated 55 minute(s) ago.

  1. Al, we have two gantry cranes in two of our...

    Al, we have two gantry cranes in two of our buildings, one a 20 ton, the other a 15 ton.

    We set the rails they run on in Chockfast Gray. Just a 1/2 inch thick bed is Ann it took. We leveled the...
  2. The industry standard for the 30BR has settled in...

    The industry standard for the 30BR has settled in on a .330 neck, zero freebore, and trim to length of 1.500 to 1.510.

    Since Randy kinda invented this concept, those reamer specs have become...
  3. Mort, we have two nice magnetic base drills. But...

    Mort, we have two nice magnetic base drills. But this setup does a much better job in the field. Especially where space is limited.

    Of course, for larger holes, you need the kind of power and...
  4. Since I am quite the novice at bullet making, I...

    Since I am quite the novice at bullet making, I am curious as to what you are asking.
  5. Chockfast comes in many grades. ...

    Chockfast comes in many grades.

    https://itwperformancepolymers.com/products/chockfast

    For chicks under reduction gears and engines in boats, Chockfast Orange is used.

    Gray is used in...
  6. Close. It is a QSK 38, tier 4. I think they are...

    Close. It is a QSK 38, tier 4. I think they are set at 1300 HP. That is about max for a 38 series.

    Surprisingly, we donít see that many KT 50 series. When boats start getting into the1500+ HP per...
  7. lol

    lol
  8. Al. Those two men helping me, you could add their...

    Al. Those two men helping me, you could add their ages together and I still top them by about 20 years.

    I donít know if climbing around in these darned boats has kept me young, or made me old:p
  9. You noticed that, huh. Yes, the thread in top...

    You noticed that, huh.

    Yes, the thread in top of the drill is a left hand thread. I made the end of that 3/4 feed rod to fit it. The pillow block bearing has a threaded insert pressed into to do...
  10. Drilling Reduction Gear Foundation For Body Fit Bolts......Marine Gear Installation

    I have spent the last couple of days down in the engine room of a new 2600 HP Tug thatís being built at San Jac Marine.

    https://www.youtube.com/watch?v=gR_PJrgG3sE

    We do quite a bit of this,...
  11. Thatís a tad more serious than I guessed. I...

    Thatís a tad more serious than I guessed. I should revise my HP estimate up quite a bit.
    And the RPM. That sounds like a 7800+ rpm setup.
  12. Itís a 2018 model, it says 435 hp 6.2 liter. Itís...

    Itís a 2018 model, it says 435 hp 6.2 liter. Itís by far the nicest truck I have ever owned.

    The good thing about my trip to Phoenix is I get on I-10 about a mile from my house and donít get off...
  13. Dave, my Denali didnít quite do that good, but...

    Dave, my Denali didnít quite do that good, but going to Phoenix last year, it did this. I set the tripometer when I hit IH-10 about a mile from my house.
    ...
  14. Thread: Primers

    by jackie schmidt
    Replies
    8
    Views
    968

    Of course the brand of primer makes a big...

    Of course the brand of primer makes a big difference in the tune.

    But surely Sir Charles wasnít talking about individual primers in a box of 100.
  15. Replies
    22
    Views
    2,163

    That middle of the road stuff isnít going to win...

    That middle of the road stuff isnít going to win anything, period.

    I never went Tony Boyerís school, but a very good friend of mine did.

    The the first morning with his Rife, he was told by Mr...
  16. Al, sounds like the Block might have had the...

    Al, sounds like the Block might have had the lifter bores enlarged to .904, a very popular modification on big blocks, but they stuck in a cam with a base circle designed for the stock .840 bores.
    ...
  17. Iím intrigued, Al. Whatís that beast going in? ...

    Iím intrigued, Al. Whatís that beast going in?

    Judging from the distance between the water pump mount and the deck, I would bet you used a 10.250 tall deck.
  18. Replies
    22
    Views
    2,163

    Didnít arguabley the best Short Range Benchrest...

    Didnít arguabley the best Short Range Benchrest Shooter ever state that in later years he weighed charges to the nearest .05 grn.
  19. Replies
    22
    Views
    2,163

    Al, if you have a Ď06, you should try that...

    Al, if you have a Ď06, you should try that Reloader 16 with bullets in the 160/170 range. It gave great velocity, no pressure signs, and cleaned up great. That is the most consistent velocities I...
  20. Replies
    22
    Views
    2,163

    Al, I had my custom 30-06 up Walker County hast...

    Al, I had my custom 30-06 up Walker County hast Sunday, just to shoot it some. Itís a 1-9 twist Krieger, Remington Varmint taper, 25 inches long. HS precision stock, trued up Rem 721, 8-32 NXS...
  21. Dave, Inland Pushboats that we work on generally...

    Dave, Inland Pushboats that we work on generally can range from about 1000 HP to 3600 HP.

    Detroitís used to be very common in the inland business, 12-71, 16-71, 12 and 16-92ís, 12 and 16 149ís...
  22. Sticky: Thanks. My wife and I are planning on making the...

    Thanks. My wife and I are planning on making the trip and camping in the MotorHome. I gues I better get a spot reserved.

    I looked at the BRRCSite, and canít seem to find the RVCamp map and what...
  23. Louis, they stay straight, that is, until a...

    Louis, they stay straight, that is, until a Captain decides to plow up the south forty.

    If you spend enough time doing this kind of work, you will understand how difficult it is to bend one off...
  24. Replies
    184
    Views
    19,813

    Yes it could be construed as an extremely short...

    Yes it could be construed as an extremely short barreled, (or no barreled), Rifle with the barrel removed. The reason.? You could chamber a round and it would fire.

    However, you would think common...
  25. Most of the run out on the coupling end usually...

    Most of the run out on the coupling end usually Is a result of the welding in repairing any corrosion in the seal area. It might not be but .010 or so thousandths, but it still has to run dead true....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4