Search:

Type: Posts; User: brickeyee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Primers

    by brickeyee
    Replies
    35
    Views
    3,851

    Thickness is NOT the only way to alter primer...

    Thickness is NOT the only way to alter primer performance and cup strength.

    The cup is punched from brass sheet stock.
    An extra strike can easily alter the hardness of the cup.

    Using slightly...
  2. Thread: Crowns

    by brickeyee
    Replies
    24
    Views
    2,436

    I had 3-phase with idlers for years. Had a neat...

    I had 3-phase with idlers for years.
    Had a neat little starter system to spin up the 3-phase idler.
    Used a rubber tire rubbing on a pulley sheave to spin up the idler.
    Pull lever, enough frictions...
  3. You only had to send the last 20 years of 4473s,...

    You only had to send the last 20 years of 4473s, and any bound books.
  4. Thread: Crowns

    by brickeyee
    Replies
    24
    Views
    2,436

    This. It takes a careful lath setup to cut a...

    This.

    It takes a careful lath setup to cut a crown.
    Some are harder than others to cut.

    Some appear to have a better chance of coming out dead on than others.

    To a certain extent a method...
  5. Replies
    12
    Views
    1,279

    Shut down all the apps on your computer....

    Shut down all the apps on your computer.
    Especially whatever you use to read the internet.
    Reboot the computer.
    This will force it to load a new copy of whatever viewer you are using from the hard...
  6. Replies
    8
    Views
    1,523

    Any number of powders have had a single...

    Any number of powders have had a single manufacturer and been sold under multiple brand names for may years.
    Canister powders (and the extra work they require to produce) are not a large market....
  7. Replies
    24
    Views
    3,704

    I did not notice he had Berger's in the list....

    I did not notice he had Berger's in the list.
    They are very much BR.
    Lapua and Nosler. he sighted are NOT BR grade.

    I have a decent pile of Starke bullet in my drawer.
    They also work VERY...
  8. Replies
    962
    Views
    510,610

    I was in the McLean VA Giant food store. A women...

    I was in the McLean VA Giant food store.
    A women was being absolutely obnoxious to the clerk.

    "Don't you know who I am?
    My husband is a US Senator."

    The poor clerk stayed clam, looked at her,...
  9. Thread: Primers

    by brickeyee
    Replies
    35
    Views
    3,851

    You do NOT want to make priming compound at home....

    You do NOT want to make priming compound at home.
    If you can even get a major fraction of the material required.
    It is NOT 'strike anywhere match heads.'
    See Cooper, "Explosives Engineering" if...
  10. Thread: Primers

    by brickeyee
    Replies
    35
    Views
    3,851

    Except precious metals can be used over and over....

    Except precious metals can be used over and over.

    Primers are a truly 'one shot' deal.
  11. noose maybe?

    noose maybe?
  12. Replies
    24
    Views
    3,704

    None of those are even close to a BR grade...

    None of those are even close to a BR grade bullet.

    I use BR 'tricks' for long range varmint hunting.
    Groundhogs at 400+ yards.
    Panda action, right bolt, left port, built by Kelbly's many years...
  13. Replies
    6
    Views
    1,888

    Tapered seat of perpendicular shoulder? A lot...

    Tapered seat of perpendicular shoulder?

    A lot of commercial actions have tapered seats.

    Panda actions have a square shoulder.
    Square shoulders are more repeatable.

    When I switch from...
  14. Replies
    54
    Views
    6,805

    https://www.sinclairintl.com/shooting-accessories/...

    https://www.sinclairintl.com/shooting-accessories/targets-amp-accessories/target-accessories/target-stamps-prod33159.aspx
  15. Replies
    6
    Views
    1,888

    Twist direction? Threaded barrel are usually...

    Twist direction?

    Threaded barrel are usually set up so the the barrel is tightened
    into the receiver by the bullet as it goes though.
  16. Usually four veins and the left internal mammary...

    Usually four veins and the left internal mammary artery.

    Treats blockages in the five major cardiac arteries.

    Sounds like you had a good surgeon.

    Try not to sneeze or cough for a few days.
    ...
  17. Replies
    54
    Views
    6,805

    Just get a BR trigger that fits your action....

    Just get a BR trigger that fits your action.
    Most are Rem 700 compatible.

    Jewell Triggers are still very very good.

    I use one on my Panda varmint rifle.
    Set at less than one ounce.
  18. Replies
    13
    Views
    3,559

    Probably a good idea. I would bet he was having...

    Probably a good idea.
    I would bet he was having an unremarkable recovery in those few days,
    so best to get him as far away from sick people as possible.

    Getting a Covid infection while...
  19. Replies
    32
    Views
    5,561

    NO. You can make as many rifles or handguns as...

    NO.
    You can make as many rifles or handguns as you want for personal use.
    Some states try and control this.
    You can then sell the gun as long as you did NOT make it with anticipation of selling...
  20. Any damage may (or may not) affect accuracy. ...

    Any damage may (or may not) affect accuracy.

    Might as well finish it up and try it out at this point.

    Hopefully you have enough metal to set it back if it does not shoot well enough.

    I will...
  21. Replies
    14
    Views
    2,996

    Carbide is a its best with heavy cuts and faster...

    Carbide is a its best with heavy cuts and faster speeds.

    Light cuts and slower speeds do not carry off the heat generated as well.

    While touching up carbide edges has gotten easier with the...
  22. Thread: Lathe Stand

    by brickeyee
    Replies
    3
    Views
    1,249

    Looks like the top of the stand has been left...

    Looks like the top of the stand has been left with a lip to form a chip tray.
  23. Replies
    4
    Views
    1,366

    Cup thickness is NOT the only way to alter primer...

    Cup thickness is NOT the only way to alter primer cup strength.
    An extra strike during forming will work harden the brass more.
  24. Replies
    34
    Views
    7,904

    A hole EXPANDS as if it was filled with the same...

    A hole EXPANDS as if it was filled with the same material.
    That means the hole gets LARGER.
  25. Replies
    18
    Views
    3,994

    Looks like tool chatter. As in holder not tight...

    Looks like tool chatter.
    As in holder not tight enough.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4