Search:

Type: Posts; User: blades; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    19
    Views
    736

    trick is to have the proper jig and the method to...

    trick is to have the proper jig and the method to keep the body of the bolt cool. Otherwise there is the possibility of warping the bolt body. Just to put some sanity back in the thread.
  2. Replies
    4
    Views
    222

    possibly an overall length gauge. 2nd...

    possibly an overall length gauge. 2nd possibility is a unit to make sure the pill is concentric with the case. perhaps, a false muzzle for cleaning. Lastly just another dodad to lighten your...
  3. Replies
    24
    Views
    1,743

    county, state, and local zoning ordinances, and...

    county, state, and local zoning ordinances, and your local police chief has to sign off ( unless that requirement has been rescinded). posted hours of operation for the Feds. With some of the new...
  4. Thread: $50 Borescope

    by blades
    Replies
    15
    Views
    1,932

    it can find and look at the internal end of the...

    it can find and look at the internal end of the gas port and everything around it though. unless of course it happens to be a smaller cal. than .22 rf . I have one after the initial reviews- can't...
  5. Replies
    816
    Views
    397,678

    Wish List?

    Wish List?
  6. Replies
    4
    Views
    715

    might want to check with Butches if that mixture...

    might want to check with Butches if that mixture is safe for o-rings and piston seals in an air rifle- they are completely different units than a powder burner and some of our powder burner goodies...
  7. Replies
    2
    Views
    768

    good move for them - no question as to why. When...

    good move for them - no question as to why. When I read about the fire it seemed that it was a total loss equipment wise. Fresh start in a Friendly state. Perhaps there was a silver lining in that...
  8. Thread: one piece rests

    by blades
    Replies
    12
    Views
    1,292

    My goodness I sure do live in the dark ages.

    My goodness I sure do live in the dark ages.
  9. Thread: Silly Puddy

    by blades
    Replies
    24
    Views
    2,730

    duct seal

    duct seal
  10. Replies
    29
    Views
    4,227

    That applies to all machine tools fixed portable...

    That applies to all machine tools fixed portable or hand held- dang things have no respect for your appendages, or for that matter your torso either.
  11. Replies
    11
    Views
    2,522

    try center x in that cz you might be surprised, ...

    try center x in that cz you might be surprised, flyers are not always ammo related, any of us could write a 10 page dissertation on that and it would barely break the surface. Just to really mess...
  12. Replies
    4
    Views
    707

    I think I remember Dan as being the one offering...

    I think I remember Dan as being the one offering to build them. Could be off base here though as that was quite awhile ago. found some u tube stuff from back in 2013 and before. I have not been...
  13. Replies
    18
    Views
    4,590

    scanned through a bunch of reviews -yep- works...

    scanned through a bunch of reviews -yep- works with windows 7- which is my op system.
  14. Replies
    59
    Views
    9,603

    many years ago a customer called and complained...

    many years ago a customer called and complained about his newly installed lathe- intermittent rough cuts and intermittent out round spots in longer length cuts. He could not quite grasp the thought...
  15. i have a target model 70 you speak of in 06, gun...

    i have a target model 70 you speak of in 06, gun is stamped national match- it still holds the x ring with room to spare at 600 yards if I do my part. was feeding it 168, 180,190 bthp over a nice...
  16. Replies
    3
    Views
    1,019

    like Tim said better scope and higher...

    like Tim said better scope and higher magnification. if shooting for a group I hope you are using point of aim as a reference and have the scope set off to any other area so as to not destroy point...
  17. Replies
    5
    Views
    966

    Browning- trade name only now days forget who...

    Browning- trade name only now days forget who owns the rights to it. Winchester same deal. Remminton, Savage, Colt, S&W part of corporate conglomerates now days. Think Ruger is about the only large...
  18. Replies
    9
    Views
    2,242

    lot of variables but that is a good base price.

    lot of variables but that is a good base price.
  19. Thread: Pcp pumps

    by blades
    Replies
    11
    Views
    1,337

    Actually you are not far off quite a Few years...

    Actually you are not far off quite a Few years back Before the big hack) a couple of enterprising individuals took a hand pumps and motorized them using that basic principal. Cooling systems had...
  20. Thread: Pcp pumps

    by blades
    Replies
    11
    Views
    1,337

    I used the German ones when first starting out. ...

    I used the German ones when first starting out. Freedom 10 shoebox compressor direct websight.
  21. Thread: Pcp pumps

    by blades
    Replies
    11
    Views
    1,337

    decent hand pump with a filter is in the $250...

    decent hand pump with a filter is in the $250 area. Powered pumps inexpensive Chi-com units mostly a waste of money. Generally it is a 50/50 shot if they work out of the box and do not last long. ...
  22. Replies
    36
    Views
    6,381

    No replacement for displacement. particularly...

    No replacement for displacement. particularly when hauling whatever. Put the 6x10 trailer behind my Escape (2L turbo) drops from apx 29+ to 15 mpg ( empty trailer) load it up down to 12 or less...
  23. Thread: Bullet weld?

    by blades
    Replies
    46
    Views
    5,959

    And the big boys run in to glitches as well. I...

    And the big boys run in to glitches as well.
    I have never had a detonation that i am aware of, but I did have light loads/ insufficient powder in a 375 Weatherby ( starting loads for 375 HH), of...
  24. Thread: Bullet weld?

    by blades
    Replies
    46
    Views
    5,959

    Guess I am too old school , Yes I use a...

    Guess I am too old school , Yes I use a thrower-have a few, I always throw Short and trickle up on a beam scale, I do not trust the electronic ones, they might be better now days but they float to...
  25. i have 2 set ups that indicate left right and up...

    i have 2 set ups that indicate left right and up down at the same time . extremely sensitive as they will indicate thermal currents in a no breeze scenario. on the other hand if it gets too breezy...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4