Search:

Type: Posts; User: Al Nyhus; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    808

    If the bolt shroud is original to the action, the...

    If the bolt shroud is original to the action, the serial number is also engraved on one of the bottom flats of the shroud.

    I recently rehabed a 1375. After quite a bit of work on the cocking...
  2. Replies
    50
    Views
    16,165

    Having seen results first hand from Rem Clean...

    Having seen results first hand from Rem Clean use, it will never get used in my barrels.

    In my 30BR, a .338 bronze brush wet with Butch's pushed to the end of the neck and turned a few times...
  3. Replies
    50
    Views
    11,074

    Those are for the sensors for each cylinder....

    Those are for the sensors for each cylinder. Probes go into each one and send the information from the exhaust to the RacePak computer. The RacePak then displays it as fuel/air ratio for each...
  4. Replies
    50
    Views
    11,074

    It looks like you're making good power with the...

    It looks like you're making good power with the '64, Dave. :) -Al
  5. Replies
    50
    Views
    11,074

    Todays project wasn't as fun but just as...

    Todays project wasn't as fun but just as necessary.....the supercharged Coyote 5.0 came out of the Cobra Jet for a freshen up. These are like 10 lbs of poo in a 5 lb sack in the engine bay. The...
  6. Replies
    8
    Views
    932

    They have one of the beater hammers there too....

    They have one of the beater hammers there too. They used a piece of aluminum/bronze channel over the flat part of the wrench that the hammer impacted. -Al
  7. Replies
    50
    Views
    11,074

    On the schedule last week was this well worked...

    On the schedule last week was this well worked out 283 SBC NHRA Super Stock engine. Over the course of several days, three different camshafts were evaluated as well as some rather unconventional...
  8. Replies
    8
    Views
    932

    This is on display at the Gavins Point Dam close...

    This is on display at the Gavins Point Dam close to where I live....it's for the turbine shaft. My size 11 is for reference. -Al

    https://i.imgur.com/FwvzGobl.jpg
  9. Thread: Imgur

    by Al Nyhus
    Replies
    14
    Views
    980

    If your question is how to get the pic from imgur...

    If your question is how to get the pic from imgur to appear in your message w/o the need for anyone clicking a link:

    Just click on your pic in imgur. The image will open in a new larger...
  10. Replies
    37
    Views
    3,438

    No worries. :) The case neck not being straight...

    No worries. :) The case neck not being straight relative to the long axis of the case body and the 'banana case' thing are two seperate situations. For a time, I bought into the 'banana case' theory...
  11. Replies
    15
    Views
    1,936

    Couldn't agree more. Good shootin' :) -Al

    Couldn't agree more.

    Good shootin' :) -Al
  12. Replies
    11
    Views
    1,417

    Just rinsed 1,000 new J4's in acetone this...

    Just rinsed 1,000 new J4's in acetone this morning. This is the acetone after sitting for 30 minutes post rinsing to allow any residue to settle. Then it got poured through a paint strainer to show...
  13. Replies
    11
    Views
    1,417

    I've also used standard lacquer thinner, mineral...

    I've also used standard lacquer thinner, mineral spirits and camp stove fuel to wash jackets. Other than the evaporation time, they all do a good job.

    I absolutely would not use Ronsonol. :(...
  14. Replies
    11
    Views
    1,417

    Though I've never used hexane, it appears that it...

    Though I've never used hexane, it appears that it would do a good job. :) -Al
  15. Replies
    37
    Views
    3,438

    The necks need to be straight relative to the...

    The necks need to be straight relative to the case body before doing any inside neck work, obviously.....
  16. Replies
    2
    Views
    522

    Will do! -Al

    Will do! -Al
  17. Replies
    37
    Views
    3,438

    My setup to ream necks: Wilson trimmer and...

    My setup to ream necks:

    Wilson trimmer and neck reamer:

    https://i.imgur.com/bwS4ROjl.jpg

    Fit of the Wilson neck reamer:

    https://i.imgur.com/Joz546Il.jpg
  18. Replies
    37
    Views
    3,438

    When you neck up a smaller diameter neck to a...

    When you neck up a smaller diameter neck to a larger diameter neck, the bottom portion of the new larger diameter neck is what used to be the shoulder. The shoulder area is considerably thicker than...
  19. Replies
    37
    Views
    3,438

    If you're using a Wilson trimmer, you'll want a...

    If you're using a Wilson trimmer, you'll want a case holder for the 220R for the cases prior to them being f-formed. Then you'll need the case holder for the PPC family for trimming.

    With the...
  20. Replies
    37
    Views
    3,438

    My system is very much like this one pictured in...

    My system is very much like this one pictured in Tony Boyer's book. I had Wilson make up reamers in .0005 increments. A lathe made steel bushing aligns and supports the reamer in the holder.
    ...
  21. Replies
    37
    Views
    3,438

    After expanding, the lower portion of the neck is...

    After expanding, the lower portion of the neck is what used to be the upper shoulder area. Consequently, the I.D. of the lower portion of your newly expanded neck is going to be smaller than the I.D....
  22. Replies
    15
    Views
    2,156

    Hunter, I probably didn't phrase my question...

    Hunter, I probably didn't phrase my question correctly so I'll try again.

    Have you verified the chamber length (with a chamber length gauge) so there's no possibility that any of the necks are...
  23. My first thought also. -Al

    My first thought also. -Al
  24. Thread: 8208

    by Al Nyhus
    Replies
    6
    Views
    1,186

    Jerry, I've got three flavors of 8208's...

    Jerry, I've got three flavors of 8208's here...IMR 8208 'pull down', some other type of strange 8208 that predates the 'pull down' :confused: and the latest XBR8208. They're different based on what I...
  25. An improved 700 action is on the Remington 'Alpha...

    An improved 700 action is on the Remington 'Alpha 1' rifles.

    https://www.remarms.com/rifles/bolt-action/model-700/model-700-alpha-1
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4