Search:

Type: Posts; User: Michael Huebner; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    8
    Views
    2,565

    [QUOTE=jackie schmidt;828602] ...

    My understanding is the reason has nothing to do with the quality or the numbers sold. I wouldn’t own one if the quality was not exceptional.
  2. Replies
    29
    Views
    4,354

    I will be interested on how they will go...

    I will be interested on how they will go especially without any dampening.
    Did the original ones not have any?

    I have two of the Beggs units with plastic dampers, so curious how the original...
  3. Replies
    61
    Views
    7,187

    I use the one pictured only difference mine has a...

    I use the one pictured only difference mine has a chamfer on the stem to get close to the neck/shoulder junction. Back around 20yrs ago Russ Hayden or Ron Hoehn used to sell them with the chamfer.
    ...
  4. Replies
    2
    Views
    877

    Pin

    Roughly 0.060” if it’s a Rem700
    What does yours measure?
  5. eBay. Do a search for the size you are looking for

    eBay. Do a search for the size you are looking for
  6. Replies
    12
    Views
    1,845

    BAT do this as well

    I have a BAT Model 'B' action with the same
  7. Bearings

    You don't need bearings, unless you want to.
    Drill and tap the top of the Delrin for a Stainless Grub Screw and make the shaft with a sharp point.
    That's all you need

    Michael
  8. Replies
    20
    Views
    5,333

    Flavio Trigger

    Does Killough shooting sports still bring them into USA?
    They are still being made and we can get them this side of the pond
    Out if interest what are you testing?
    Michael
  9. Replies
    38
    Views
    5,226

    Good Idea

    Kyle it’s a good idea. As you know it takes about 3 x firings to obtain full shape, so nil issues swapping to the actual barrel after the first fire form load.

    Michael
  10. Replies
    31
    Views
    6,860

    Well I am interested

    No one Inetrested
  11. Vfd

    I know you may not want to here this, but I think you may have purchased the wrong device and maybe a rotary phase converter was a better option....
  12. Replies
    32
    Views
    6,352

    The ‘duty cycle’ I refer has nothing to do with...

    The ‘duty cycle’ I refer has nothing to do with the semiconductors, it is the braking resistor. You can over rate the power of the resistor but the cost would outweigh the benefit for hobby type...
  13. Replies
    32
    Views
    6,352

    Keeping in mind that you need to consider duty...

    Keeping in mind that you need to consider duty cycle when using braking resistors especially if you desire an almost instant stop.
    And not all VFD’s have the feature, especially some budget versions.
  14. Vfd

    I used the Hitachi Wj200-022sf Variable Frequency Drive 3 HP 230 VAC Single Phase Input which is in the next bracket around $300.
    Also depending on how safe you want the installation to be, you...
  15. The Accurate Rifle - Warren Page

    THE ACCURATE RIFLE - WARREN PAGE

    I tend to agree, that is why I claim the exact touch with a magnifier or smoked bullet or the YouTube above etc does not really matter so much.
    The Hornady tool...
  16. I actually do both. I use the Hornady tool which...

    I actually do both. I use the Hornady tool which probably has it in a couple of thous at touch.

    But the hard jam comes from there is only one way to go - push bullet back into case. Pretty sure it...
  17. Replies
    7
    Views
    2,736

    Yes it has been discontinued. When the current...

    Yes it has been discontinued. When the current stock runs out that is it. No new scope.
    They pointed me to there variable 15-55 as another option (which I said was to heavy) or they could advise me...
  18. Agreed to definition That’s why it doesn’t...

    Agreed to definition

    That’s why it doesn’t matter as long as you do it the same each time.
    Once you have the starting point the adjustments in or out and the target tell you what is working.
    ...
  19. How much tension when determining the "jam"

    Answer: Nil use

    It actually doesn't matter how you go about it, as potentially you will end up in the same place. It only matters when you want to direct compare with another competitor or on...
  20. Replies
    57
    Views
    16,793

    I use a .270 neck in competition. I used to use a...

    I use a .270 neck in competition. I used to use a .263 neck (changed about 5yrs ago) and have found no issues with the .270 when using Lapua brass

    Michael
  21. Replies
    14
    Views
    3,285

    Do a search up in the top right hand corner for...

    Do a search up in the top right hand corner for "Barrel Flush System" and a lot of information will come up about design and use. That may help you get started
  22. Small Base

    0.200 Mark (up from base), but I am not sure what is classified as small base. If you are referring to a Redding die they aren't all the same, so you will need to try it.

    Michael
  23. Replies
    8
    Views
    2,016

    TS3 - Carbide Depot

    TS3 - Carbide Depot
  24. Thread: ppc ?

    by Michael Huebner
    Replies
    29
    Views
    6,403

    You won’t go wrong anywhere from .263 to 0.270...

    You won’t go wrong anywhere from .263 to 0.270
    Virgin Lapua 220 measures about 0.0148 to 0.0152
    If you are running around the 0.003 clearance you will be neck turning to around 0.0118 for a 270...
  25. Replies
    27
    Views
    4,825

    Have to say I agree with Al, as I was one of...

    Have to say I agree with Al, as I was one of these fortunate 'lucky' people.

    I won a Yardage and a Grand/Agg at my first Group Nationals. Had shot only four matches prior. I later discovered I...
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4