Search:

Type: Posts; User: geo.ulrich; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds; generated 27 minute(s) ago.

  1. Jackie, The Cactus is still on. I think you will...

    Jackie, The Cactus is still on. I think you will be safe, just don't stop for chinese for dinner.....
  2. Replies
    4
    Views
    1,805

    he was as of a few weeks ago...

    he was as of a few weeks ago...
  3. Replies
    23
    Views
    4,437

    [QUOTE=Rubicon Prec.;831491]Can one honestly...

    [QUOTE=Rubicon Prec.;831491]Can one honestly qualify a +/-.0001” tolerance in a home garage shop with a mic?

    I think the .002” window (+/-.001”) stated above is more realistic.

    everybody here...
  4. Replies
    8
    Views
    2,078

    Jackie , you will be happy with the hines 30's...

    Jackie , you will be happy with the hines 30's ....
  5. Replies
    1
    Views
    804

    Yes they are the same the only thing changed was...

    Yes they are the same the only thing changed was ejection pin diameter to give more or less bearing length.....
  6. Replies
    33
    Views
    5,517

    This will be a little long. Years ago a H.O.F....

    This will be a little long. Years ago a H.O.F. shooter was complaining his barrel done by another top br gunsmith was not shooting actually a few. I told him bring it by work I wanted to check...
  7. Replies
    33
    Views
    5,517

    Bingo there you go......

    Bingo there you go......
  8. Replies
    3
    Views
    1,038

    Jackie, They would be 1.150

    Jackie, They would be 1.150
  9. Replies
    11
    Views
    1,737

    when you say "raw" do you mean xxxxx

    when you say "raw" do you mean xxxxx
  10. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    Yep its just an expandable plastic mesh....I just...

    Yep its just an expandable plastic mesh....I just pinched them and didn't worry about edge it wasn't like i was going to make millions just meant a sore thumb from pointing
  11. Replies
    3
    Views
    623

    Don Unmusigg Richmond Va. if you need phone# I...

    Don Unmusigg Richmond Va. if you need phone# I will send a p.m.
  12. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    As I said in post #2 I make them myself , well...

    As I said in post #2 I make them myself , well because I can and it really doesn't cost me anything but time. it was an experiment to see if it would help at 200 with wind drift as compared to the 30...
  13. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    well I guess they don't exist here's an 18 twist...

    well I guess they don't exist here's an 18 twist kreiger blank . what twist would you use for a .875 long 85/ 100 gr. bullet I have maybe 5-6 16/18 twist from just about as many Co.'s
  14. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    what twist barrel do you have? I used 16/17 for...

    what twist barrel do you have? I used 16/17 for the short br bullets I think they were about .890 in length .
  15. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    Its not the bullets its jackets we can make great...

    Its not the bullets its jackets we can make great bullets in any caliber. Of course if what you said is true we would still be shooting 22's in 222. or flintlocks ;)
  16. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    3,914

    I have played with 7br with bullets in the...

    I have played with 7br with bullets in the 85-100 gr area it works great for score especially for 200 it doesn't drift near as much as the 30 br. velocity for a 100gr is 3300 fps. the problem...
  17. Replies
    50
    Views
    5,631

    This works great other than I use epoxy resin...

    This works great other than I use epoxy resin with glass powder to make it into a putty....^^^^^^^^^ and a grommet on bottom for screws to pull against
  18. Replies
    15
    Views
    1,670

    them is the ones....

    them is the ones....
  19. Replies
    15
    Views
    1,670

    Al, again STRAIGHT FLUTE CARBIDE key seat...

    Al, again STRAIGHT FLUTE CARBIDE key seat cutters not helixed. actions are hard but not real bad just take it easy over the base holes thats where corners will get chipped
  20. Replies
    15
    Views
    1,670

    Hence the reason for the 2 flute straight flute...

    Hence the reason for the 2 flute straight flute key seat cutters no felix less torquing
  21. Replies
    15
    Views
    1,670

    Funny they have been finishing slots with on size...

    Funny they have been finishing slots with on size end mills for years. look at electric motor shafts or printing rolls ....unless it NEEDS to be press fit cutting both sides just wastes time. and in...
  22. Replies
    15
    Views
    1,670

    You could also clamp straight to table against...

    You could also clamp straight to table against pins and use a milling cutter on arbor at 90* try the straight flute cutters they are made in stub length the helixed cutters have a higher shear...
  23. Replies
    25
    Views
    4,228

    Another loss to Bench Rest, he was one of the...

    Another loss to Bench Rest, he was one of the best the sport offered... R.I.P.
  24. Replies
    15
    Views
    1,670

    Al, Rough slot first 3/16 then finish with a 1/4...

    Al, Rough slot first 3/16 then finish with a 1/4 I would go with straight flute carbide key seat cutters..what rpm are you running at
  25. Hello Bill hope your doing well. ...

    Hello Bill hope your doing well. EQUIPMENT,EQUIPMENT,EQUIPMENT
Results 1 to 25 of 493
Page 1 of 20 1 2 3 4