Search:

Type: Posts; User: geo.ulrich; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    3
    Views
    248

    Jackie, They would be 1.150

    Jackie, They would be 1.150
  2. Replies
    11
    Views
    594

    when you say "raw" do you mean xxxxx

    when you say "raw" do you mean xxxxx
  3. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    Yep its just an expandable plastic mesh....I just...

    Yep its just an expandable plastic mesh....I just pinched them and didn't worry about edge it wasn't like i was going to make millions just meant a sore thumb from pointing
  4. Replies
    3
    Views
    208

    Don Unmusigg Richmond Va. if you need phone# I...

    Don Unmusigg Richmond Va. if you need phone# I will send a p.m.
  5. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    As I said in post #2 I make them myself , well...

    As I said in post #2 I make them myself , well because I can and it really doesn't cost me anything but time. it was an experiment to see if it would help at 200 with wind drift as compared to the 30...
  6. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    well I guess they don't exist here's an 18 twist...

    well I guess they don't exist here's an 18 twist kreiger blank . what twist would you use for a .875 long 85/ 100 gr. bullet I have maybe 5-6 16/18 twist from just about as many Co.'s
  7. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    what twist barrel do you have? I used 16/17 for...

    what twist barrel do you have? I used 16/17 for the short br bullets I think they were about .890 in length .
  8. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    Its not the bullets its jackets we can make great...

    Its not the bullets its jackets we can make great bullets in any caliber. Of course if what you said is true we would still be shooting 22's in 222. or flintlocks ;)
  9. Thread: 7br?

    by geo.ulrich
    Replies
    31
    Views
    1,607

    I have played with 7br with bullets in the...

    I have played with 7br with bullets in the 85-100 gr area it works great for score especially for 200 it doesn't drift near as much as the 30 br. velocity for a 100gr is 3300 fps. the problem...
  10. Replies
    45
    Views
    2,211

    This works great other than I use epoxy resin...

    This works great other than I use epoxy resin with glass powder to make it into a putty....^^^^^^^^^ and a grommet on bottom for screws to pull against
  11. Replies
    15
    Views
    1,063

    them is the ones....

    them is the ones....
  12. Replies
    15
    Views
    1,063

    Al, again STRAIGHT FLUTE CARBIDE key seat...

    Al, again STRAIGHT FLUTE CARBIDE key seat cutters not helixed. actions are hard but not real bad just take it easy over the base holes thats where corners will get chipped
  13. Replies
    15
    Views
    1,063

    Hence the reason for the 2 flute straight flute...

    Hence the reason for the 2 flute straight flute key seat cutters no felix less torquing
  14. Replies
    15
    Views
    1,063

    Funny they have been finishing slots with on size...

    Funny they have been finishing slots with on size end mills for years. look at electric motor shafts or printing rolls ....unless it NEEDS to be press fit cutting both sides just wastes time. and in...
  15. Replies
    15
    Views
    1,063

    You could also clamp straight to table against...

    You could also clamp straight to table against pins and use a milling cutter on arbor at 90* try the straight flute cutters they are made in stub length the helixed cutters have a higher shear...
  16. Replies
    22
    Views
    2,053

    Another loss to Bench Rest, he was one of the...

    Another loss to Bench Rest, he was one of the best the sport offered... R.I.P.
  17. Replies
    15
    Views
    1,063

    Al, Rough slot first 3/16 then finish with a 1/4...

    Al, Rough slot first 3/16 then finish with a 1/4 I would go with straight flute carbide key seat cutters..what rpm are you running at
  18. Hello Bill hope your doing well. ...

    Hello Bill hope your doing well. EQUIPMENT,EQUIPMENT,EQUIPMENT
  19. I met Jim early when Harrison started holding...

    I met Jim early when Harrison started holding matches, He was a great guy to be around and a great shooter...
  20. Replies
    25
    Views
    4,250

    Jackie, Looks like you got all working good...

    Jackie, Looks like you got all working good luck...:D
  21. Thread: tpi to M

    by geo.ulrich
    Replies
    28
    Views
    3,814

    exactly ^^^

    exactly ^^^
  22. Thread: tpi to M

    by geo.ulrich
    Replies
    28
    Views
    3,814

    Minor dia. is .691. turn to .708 there will be...

    Minor dia. is .691. turn to .708 there will be .0085 left per side of vee. when you pick up thread pick up at center of length there is only .002 difference in pitch at 1" long. you will cut .001 off...
  23. Thread: tpi to M

    by geo.ulrich
    Replies
    28
    Views
    3,814

    Johan, 3/4 24 = .750 x .0416 per revolution , ...

    Johan, 3/4 24 = .750 x .0416 per revolution , 18 mm = .708 x .03937 per revolution it will work fine when returned and threaded
  24. Replies
    2
    Views
    1,110

    Gerald Forys

    St.Louis B.R. shooter Gerald Forys Passed away this afternoon. He was a fierce competitor and a great shooter... R.I.P. George
  25. Replies
    1
    Views
    1,028

    and next 22931

    and next 22931
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4