Search:

Type: Posts; User: Dave Tooley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: Question

    by Dave Tooley
    Replies
    3
    Views
    667

    Nez, I wouldn't be concerned about the strength....

    Nez,
    I wouldn't be concerned about the strength. Plenty of meat left for wall strength.
  2. Replies
    75
    Views
    6,675

    Al, I think they have been two separate...

    Al,
    I think they have been two separate companies for some time now. Steve Dahlke, who owns Criterion, used to run Kreiger.
  3. Replies
    8
    Views
    1,038

    Time and temperature dictate the end product. My...

    Time and temperature dictate the end product. My guess is BAT is staying on the conservative side of the curve.
  4. Replies
    2
    Views
    656

    You can manage the heat checking with abrasives...

    You can manage the heat checking with abrasives but at some point it's a losing battle. I would have plans in place for a replacement barrel.
  5. 👍👍👍👍 I am humbled in his presence.

    👍👍👍👍

    I am humbled in his presence.
  6. If you don't have confidence in your setup you...

    If you don't have confidence in your setup you need a different setup.
  7. Replies
    27
    Views
    2,583

    I can't get any more rotation after about 85...

    I can't get any more rotation after about 85 ft/lbs. I use 100 ft/lbs at the most.
  8. Replies
    27
    Views
    2,583

    Al Yes there is a load on the tenon pushing it...

    Al

    Yes there is a load on the tenon pushing it forward but there is also a load transferred to the threaded joint by chamber expansion. The larger the case diameter the more it expands and the...
  9. Replies
    6
    Views
    1,175

    1. not really 2. not so idiotic 3. can't say

    1. not really
    2. not so idiotic
    3. can't say
  10. Thread: Kroil?

    by Dave Tooley
    Replies
    47
    Views
    5,920

    It sure does. After it was changed I found a...

    It sure does. After it was changed I found a gallon at a gun show. That lasted me for years. When I moved a couple of years ago I still had about a cup left. I had a lot of SH.T ,stuff to move and...
  11. Replies
    9
    Views
    1,075

    Well I would guess it has a .272" diameter neck...

    Well I would guess it has a .272" diameter neck and it's an 8 twist Kreiger.
  12. Replies
    31
    Views
    3,282

    I use one at a time. Fewer to pick up afterwards....

    I use one at a time. Fewer to pick up afterwards. If you're concerned about surface area go with a bigger single patch and use a smaller jag.
  13. Replies
    17
    Views
    2,957

    Not cheap but I use Pro Ears Gold NRR 30. I wear...

    Not cheap but I use Pro Ears Gold NRR 30. I wear them with plugs and can hear range commands. I wish I had spent the money for a really good pair 40 years ago.
  14. Replies
    19
    Views
    2,535

    It's humanly impossible to wear the lugs out...

    It's humanly impossible to wear the lugs out without the use of an abrasive. Even then it will function just fine.
  15. Replies
    19
    Views
    2,535

    [QUOTE=ArtinNC;823846] You haven't explained...

    [QUOTE=ArtinNC;823846]

    You haven't explained what your problem is.
  16. Replies
    19
    Views
    2,535

    Without the action in hand there are to many...

    Without the action in hand there are to many surfaces in play to provide an informed answer.

    Just a guess from a million miles away. You changed the distance between the cocking piece and the rear...
  17. Replies
    7
    Views
    1,763

    Give him a call. They get bothered with much less...

    Give him a call. They get bothered with much less relevant questions daily. Your question is a legit. Just keep it short and to the point.
  18. Replies
    7
    Views
    1,763

    Talk to Jim Borden and explain what you want to...

    Talk to Jim Borden and explain what you want to do. He'll take care of you.
  19. Replies
    8
    Views
    1,197

    Jackie, When I was chambering on my 10" Nardini...

    Jackie,
    When I was chambering on my 10" Nardini I could do everything in about 2 1/2 hours. That's without a flush system and before I started using caliber specific core drills to rough in the...
  20. Replies
    20
    Views
    2,298

    I'm running an Aloris tool post on my Haas so I...

    I'm running an Aloris tool post on my Haas so I have to work a bit harder. Machine cycle time for most chambers, turn (maybe twice), chamfer ( maybe twice), thread relief groove(maybe), thread, rough...
  21. Replies
    47
    Views
    6,814

    I have to cover rule #1. Don't do anything to...

    I have to cover rule #1. Don't do anything to make the phone ring. That includes those horrific rings on the brass so i do a quick polish with 240.
    But really it depends on the reamer. Not all cut...
  22. Replies
    20
    Views
    2,298

    Setup is about 99% of it.

    Setup is about 99% of it.
  23. Replies
    8
    Views
    1,197

    Pete, I can comfortably do 50 a week to include,...

    Pete,
    I can comfortably do 50 a week to include, serializing, chamber, thread muzzle and Cerakote, packed ready for FedEx to pick up. It's not what the machine can do but how fast I want to feed...
  24. Replies
    20
    Views
    2,298

    2211322114 I use gage pins on the muzzle these...

    2211322114
    I use gage pins on the muzzle these days.
    For shorter barrels I have bushing that go inside the spindle. That can drive you nuts thinking about the best way to do that. I'll just say...
  25. Replies
    20
    Views
    2,298

    22112 Jackie, This is my setup. Same setup as...

    22112
    Jackie,
    This is my setup. Same setup as on a manual machine.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4