Search:

Type: Posts; User: brickeyee; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.57 seconds.

  1. Replies
    17
    Views
    2,351

    Well a 100 watt bulb was good enough for an EZ...

    Well a 100 watt bulb was good enough for an EZ Bake oven.

    Filament is more than 2,000 F.
  2. Replies
    9
    Views
    966

    You can make notes in the margins. Almost always...

    You can make notes in the margins.
    Almost always worth a look.

    After 35+ years in the EW field I still had a boat load of books and IEEE articles with tons of notes in them.
    Always print one...
  3. Replies
    11
    Views
    1,095

    Touch screens just do not work as well as actual...

    Touch screens just do not work as well as actual keyboards.
  4. Replies
    12
    Views
    1,373

    Peeing on your hands is NOT a recommended method.

    Peeing on your hands is NOT a recommended method.
  5. Replies
    9
    Views
    1,045

    The ammonia evaporate out rather rapidly.

    The ammonia evaporate out rather rapidly.
  6. Swap in a 3-phase motor and a VFD to feed it. ...

    Swap in a 3-phase motor and a VFD to feed it.

    It really is an outstanding safety feature.

    It does work better with a geared drive, but is still reasonably effective on a belt system.
  7. Replies
    17
    Views
    2,351

    Or at least the props and the shafts driving...

    Or at least the props and the shafts driving them.
    The energy stored in a prop shaft and prop as they turn is downright scary.
  8. Replies
    9
    Views
    1,045

    Sweets 7.62 Solvent Do NOT leave it in for...

    Sweets 7.62 Solvent
    Do NOT leave it in for longer than recommended.

    It is potent stuff.
    I would try and actual lead lap and very fine compound.
    Maybe just rouge initially.

    Cast the lap in...
  9. Replies
    24
    Views
    1,987

    Not a whole lot at the Federal level. Local laws...

    Not a whole lot at the Federal level.
    Local laws may say more.
  10. Replies
    12
    Views
    1,373

    It is very difficult for particles of most metals...

    It is very difficult for particles of most metals to penetrate all that far though the skin.

    In many cases the solvents used to try and clean up the surface of the skin are actually the largest...
  11. Thread: tpi to M

    by brickeyee
    Replies
    28
    Views
    4,538

    Drawings and machine tools have been in decimal...

    Drawings and machine tools have been in decimal inches for a very long time for precision work.

    Think micro-inches for super precise things.
    One millionth of an inch, 1E-6 inch.


    Not to be...
  12. Thread: resolution

    by brickeyee
    Replies
    8
    Views
    1,516

    Same sh|t, different decade. S^2, D^2

    Same sh|t, different decade.
    S^2, D^2
  13. Thread: tpi to M

    by brickeyee
    Replies
    28
    Views
    4,538

    When something is 'idiot proof' a better idiot is...

    When something is 'idiot proof' a better idiot is going to emerge.
  14. Replies
    36
    Views
    4,833

    I have a Panda Action with R-bolt, L-Port....

    I have a Panda Action with R-bolt, L-Port.
    Single feed by hand.
    It was assembled by Kelbly’s.

    It is very very accurate.
    One barrel in .22-250 AI, one in 6mm REM AI.
    Both are tight necks. Brass...
  15. Replies
    13
    Views
    2,881

    ITAR does not apply to only 'gun parts." It...

    ITAR does not apply to only 'gun parts."

    It applies to all sorts of technology that has military applications.

    The 'US Munitions List' is a good part of it.

    It defines many of the...
  16. Replies
    22
    Views
    3,833

    You really need a condition that stays around...

    You really need a condition that stays around long enough for your string.or repeats soon enough.

    I used wind flags up close and whatever was in the field further out for varmints.

    Grain crops...
  17. Replies
    5
    Views
    1,236

    It only takes on bad DNS table in that chain.

    It only takes on bad DNS table in that chain.
  18. Replies
    13
    Views
    2,881

    Australia is part of ANZUS. We have extensive...

    Australia is part of ANZUS.
    We have extensive relationships with them at very high classification levels.
    Of course only 3-latter agency workers & contractors know about them, and we cannot...
  19. Thread: tpi to M

    by brickeyee
    Replies
    28
    Views
    4,538

    One of the problems is the threading shaft pitch...

    One of the problems is the threading shaft pitch on the lathe.
    A 0.10 pitch drive is a real bear to alter to metric with gears.
    Keep in mind that gears only come in whole numbers of teeth.
    So you...
  20. Thread: tpi to M

    by brickeyee
    Replies
    28
    Views
    4,538

    One of the things we used to do at one of my...

    One of the things we used to do at one of my previous employers
    was use opponents equipment in testing US equipment.
    Everything from guns to radar sets.

    It was a well paying niche business.
    In...
  21. Thread: tpi to M

    by brickeyee
    Replies
    28
    Views
    4,538

    Cutting metric threads on a US pitched lathe has...

    Cutting metric threads on a US pitched lathe has the same problem.
    You really need change gears in some different sizes than usual to pull it off.

    If the threaded run is short you can pull it off...
  22. Replies
    59
    Views
    9,763

    Years ago we had to install a larger vibration...

    Years ago we had to install a larger vibration table.

    The older 1050s model (even with upgraded control and drive electronics) just could not handle the weight of larger newer satellite equipment....
  23. Replies
    34
    Views
    5,790

    4x to 6x is a little low for longer range...

    4x to 6x is a little low for longer range varmints.

    I have it down to a lot of setup, one shot, one dead varmint.
    Maybe wait a few hours to see of any more come back up.
  24. Replies
    15
    Views
    3,192

    https://www.sinclairintl.com/reloading-equipment/c...

    https://www.sinclairintl.com/reloading-equipment/case-preparation/neck-turning/turning-expander-mandrels/carbide-expander-mandrels-prod119668.aspx

    Pick your caliber.

    You also need a holder (die...
  25. Replies
    15
    Views
    3,192

    Sinclair...

    Sinclair
    https://www.sinclairintl.com/reloading-equipment/index.htm
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4