Search:

Type: Posts; User: blades; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. superficial laceration. in other word not deep...

    superficial laceration. in other word not deep enough to require stitches. Pain is likely more from impact- bruising looks to be fairly deep. or perhaps you are on blood thinners which makes look...
  2. Replies
    5
    Views
    450

    Do not have this particular rifle but one of...

    Do not have this particular rifle but one of those extractors might be the ejector. look closely at them may not be exactly the same shape, if so important to replace in same position.
  3. Thread: Reduced Loads?

    by blades
    Replies
    18
    Views
    1,296

    You can have that much difference in charge...

    You can have that much difference in charge weight between the crusher type pressure tests and the newer more current piezo or strain gauge systems or even between lots of the same mfg and type...
  4. and electronics in the ears/chest, bits of...

    and electronics in the ears/chest, bits of plastic/glass in eyes, plastic/metal in knees, .............
  5. Replies
    20
    Views
    2,100

    that would put them at 930 -1030 deg F apx-- over...

    that would put them at 930 -1030 deg F apx-- over the top temp wise in F, if 700 F is the magic number. so methodology is still suspect. don't know much but I can generally look it up.
  6. Replies
    20
    Views
    2,100

    I though the typical temp was 700 deg F not the...

    I though the typical temp was 700 deg F not the 500-550 used I think I read that a water quench was used- hmmmm rather allowing air cooling( slow cooling rather than a shock treatment) which could...
  7. wall is worse -it dosen't move- been there more...

    wall is worse -it dosen't move- been there more than once.
  8. Thread: Sad News

    by blades
    Replies
    7
    Views
    758

    used prices I have seen equal brand new- I...

    used prices I have seen equal brand new- I switched to Sightron years ago
  9. Replies
    14
    Views
    1,908

    I am starting to lean that way ( like Lipton ) ...

    I am starting to lean that way ( like Lipton ) as the property tax and school taxes situations are way out of hand.
  10. Replies
    25
    Views
    2,779

    got mine up apx 4"+ on steel H beams the beams...

    got mine up apx 4"+ on steel H beams the beams are connected together via some welded angle iron all sitting on 6" reinforced concrete slab.

    left room for feet but stepping that step on stop...
  11. Replies
    35
    Views
    3,726

    trials and tribulations of electronic scales- ...

    trials and tribulations of electronic scales- temp sensitive, air current sensitive, electrical line interference ( FL bulbs-one of biggest culprits) turn on and let electronics stablize prior to...
  12. Replies
    10
    Views
    1,299

    Shrink fit(Interference fit) maybe like they do...

    Shrink fit(Interference fit) maybe like they do with bearings on a shaft?
  13. Replies
    4
    Views
    862

    Air stripping best done before pellet exits...

    Air stripping best done before pellet exits muzzle ( yep holes in the barrel)- Match pistols have had that for several years already - there is very little pressure left behind the pellet when it...
  14. Replies
    8
    Views
    1,839

    Boars- Your DNR needs some education on the...

    Boars- Your DNR needs some education on the reproduction rate of those destructive vermin. Particularly if they have interbred with domestic animals.
  15. Thread: Mini lathes?

    by blades
    Replies
    18
    Views
    2,615

    I have had one of ycl 1440 for about 7-8 years...

    I have had one of ycl 1440 for about 7-8 years now- no issues to report.
  16. Replies
    26
    Views
    4,521

    Generally if you are over 50 irons become a...

    Generally if you are over 50 irons become a problem because of aging eyes. Heck I can't even use buck horns anymore, physically it is there, eyeballs say nope. Aperture types well better but not...
  17. Replies
    20
    Views
    3,476

    Machine tools - mass is your friend

    Machine tools - mass is your friend
  18. Replies
    9
    Views
    2,188

    were you using coolant on the bandsaw? ...

    were you using coolant on the bandsaw? stainless has a nasty property of workharding just a few thousands deep if it gets too warm. it gets hard enough to make getting past/through it very...
  19. Thread: Refused @ UPS

    by blades
    Replies
    27
    Views
    3,984

    truck driver - 100K not unusual any more- over...

    truck driver - 100K not unusual any more- over the road long haul. Consider than Maintenance engineers ( janitor) are in the 50k class in some areas. Fancy High rise condo in little old Milwaukee WI...
  20. Replies
    83
    Views
    33,227

    goes down better with various distilled spirits;)

    goes down better with various distilled spirits;)
  21. Replies
    30
    Views
    5,777

    I gathered that the point for purging would be...

    I gathered that the point for purging would be the interior of the barrel to prevent scaling. Choosing the proper direction of DC current flow on the tig would also help. +/- one puts more heat at...
  22. Replies
    44
    Views
    8,790

    I would guess they flood it. i have seen some...

    I would guess they flood it. i have seen some vids of that type
  23. Thread: New Lathe Ideas

    by blades
    Replies
    21
    Views
    3,644

    machine tools and any type of loose clothing or...

    machine tools and any type of loose clothing or long sleeves, long hair, gloves are a no go. don't care how slow something is moving it is always too fast. Machines don't care they just keep on...
  24. Replies
    4
    Views
    1,059

    i believe it changed owner ship- don't remember...

    i believe it changed owner ship- don't remember the details after that. Airgun Warriors is the new sight or there is GTA
  25. Replies
    4
    Views
    1,059

    can't reply to pros/cons of poly barrels not...

    can't reply to pros/cons of poly barrels not having one - pellet drift-mass vs velocity vs distance - the pellets do spiral in their trajectory, this over and above the spin from what ever type of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4