Search:

Type: Posts; User: Boyd Allen; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.78 seconds.

  1. Replies
    21
    Views
    2,060

    Does it look just like LT 32?

    Does it look just like LT 32?
  2. Replies
    21
    Views
    2,060

    I believe that the current 2015 is made in...

    I believe that the current 2015 is made in Canada, in the same plant that makes the LT powders, and has been used as a way to market lots of LT 32 that do not meet its narrow burn rate specification...
  3. Replies
    28
    Views
    2,602

    This is what I did. Taking James' direction as to...

    This is what I did. Taking James' direction as to where he had posted the picture, I opened it, copied it, and pasted it onto my computer's desktop, then I started a post and scrolled down to manage...
  4. Replies
    28
    Views
    2,602

    Here is James' picture.

    Here is James' picture.
  5. Thread: 6mm ppc

    by Boyd Allen
    Replies
    7
    Views
    1,277

    Die click story: I have a Varibase die that has...

    Die click story: I have a Varibase die that has interchangeable base bushings that have almost no chamfer. My shell holder has been shortened by about .013. I had a test case that developed a...
  6. Replies
    13
    Views
    14,435

    Next time, before you write something like this,...

    Next time, before you write something like this, you might want to do a little research. Weldable rebar is very different than the common stuff. Beyond that, the rifle is a .22 rimfire, much lower...
  7. Replies
    14
    Views
    1,627

    Jackie, Did you compare the bump that you got,...

    Jackie,
    Did you compare the bump that you got, with the same die setting, and cases that had been shot a similar number of times, no dwell to dwell? I am not saying that one would be more accurate,...
  8. Replies
    14
    Views
    1,627

    There are several variables that come into play...

    There are several variables that come into play when FL sizing. To the degree that your brass has some spring back, dwell matters, as does the amount of lube. Of course the type of lube is a factor...
  9. Replies
    31
    Views
    3,297

    Apparently I prefer a looser patch fit than you....

    Apparently I prefer a looser patch fit than you. I use a .22 piercing jag with a single, centered 1 3/8" square patch, for 6mm bores. I have never seen the advantage of squeezing the solvent out of a...
  10. Replies
    18
    Views
    3,413

    https://theshooterscorner.com/

    https://theshooterscorner.com/
  11. Replies
    9
    Views
    1,313

    If you want to know the difference between any...

    If you want to know the difference between any two FL dies of the same caliber, size a fired case with each and carefully measure both.
  12. Replies
    8
    Views
    1,405

    I would go back to the #4 die. I know that more...

    I would go back to the #4 die. I know that more shoulder sizing will increase the need to trim, but I am not clear that it presents a problem in terms of accuracy or case life. In the past I think...
  13. Replies
    16
    Views
    2,561

    For reference, the entire NBRSA rear sandbag...

    For reference, the entire NBRSA rear sandbag rule:

    2.11.2.The rear sandbag. The rear sandbag shall be a bag or combination of bags containing sand only. A vertical spacer under the rear bag will...
  14. Replies
    69
    Views
    71,313

    What is the diameter of the loaded neck. over the...

    What is the diameter of the loaded neck. over the largest diameter of the bullet? In other words I want to know how much neck tension each method is producing. Bottom line, your targets should tell...
  15. Generally, for CF rifle, there are rear bags that...

    Generally, for CF rifle, there are rear bags that are not suitable for free recoil if you are not holding the bag. One fellow that was doing well shooting free, with state of the art rifle and rest...
  16. Picture of rifle?

    Picture of rifle?
  17. When I have done this, it has been with a rifle...

    When I have done this, it has been with a rifle and rest setup that would shoot totally free, aiming it using the rest, without touching it, and only touching it with the trigger finger when firing,...
  18. Replies
    18
    Views
    2,621

    Sad news. RIP

    Sad news. RIP
  19. Replies
    11
    Views
    1,393

    Help a friend select a benchrest action

    A friend who is not on a budget is building a new rifle for benchrest and he is trying to decide what action. I told him that the Stiller 2500 would probably be what I would go with, but today he...
  20. Replies
    17
    Views
    2,390

    This insert was thread milled. I spoke with Jerry...

    This insert was thread milled. I spoke with Jerry Stiller about this detail.
  21. Replies
    17
    Views
    2,390

    I had someone give me some used barrels that were...

    I had someone give me some used barrels that were threaded for a Panda. I have an early Viper that takes a tenon with a slightly smaller pitch diameter, but which is identical to the Panda's in all...
  22. Thread: Bolt Lift

    by Boyd Allen
    Replies
    32
    Views
    5,391

    Be careful. Some of what was written in the past...

    Be careful. Some of what was written in the past was like use grinding compound of the shroud threads and other places. It may have smoothed things out, but as you know there are other...
  23. Thread: Bolt Lift

    by Boyd Allen
    Replies
    32
    Views
    5,391

    I was curious about this 15 - 20 years back, so I...

    I was curious about this 15 - 20 years back, so I colored the whole pin and spring in front of the shroud of my Viper. After a trip to the range, none of it had rubbed off of the spring or the...
  24. Thread: Bolt Lift

    by Boyd Allen
    Replies
    32
    Views
    5,391

    Doing exactly what by hand?

    Doing exactly what by hand?
  25. Thread: Bolt Lift

    by Boyd Allen
    Replies
    32
    Views
    5,391

    I think that we can look at a couple of areas to...

    I think that we can look at a couple of areas to start. We know that there has been a lot of work done on the outsides of bolts to reduce friction. Beyond durability there is the issue of heat. Some...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4