Search:

Type: Posts; User: tim; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Great choice, I have a great shooting rifle...

    Great choice, I have a great shooting rifle Penrod built.
  2. Replies
    3
    Views
    262

    Find a quality woodworker, have it made. Not a...

    Find a quality woodworker, have it made. Not a ton of $ for a great solution.
    Ken Henderson made me this one.
  3. Replies
    4
    Views
    359

    No longer needed with any quality ammo.....got...

    No longer needed with any quality ammo.....got about four different ones. For sale cheap.:D
  4. Easy, many/most will no longer do that any longer.

    Easy, many/most will no longer do that any longer.
  5. Thread: Remington 40X

    by tim
    Replies
    13
    Views
    593

    They have used Hart barrels.

    They have used Hart barrels.
  6. Thread: TRYO Bench Rests

    by tim
    Replies
    2
    Views
    396

    Indian made crap.

    Indian made crap.
  7. Talking with Kevin Nevius, a multi time national...

    Talking with Kevin Nevius, a multi time national prone champion, not BR but valid none the less, he has had great success with Kreigers which are also taper lapped. Personally, I would not hesitate...
  8. Apparently a few, but only, I guess a few. The...

    Apparently a few, but only, I guess a few. The reasons/opinions would fill a whole forum but among the largest has been bad mouthing by some self serving types.
    From guys I have talked to some...
  9. That is probably the most common dimension which...

    That is probably the most common dimension which will give you at least 24" for a 10.5 lb rifle.Anything .875"-.900" is fine.
    Shilen ratchets are popular, Muller's as well.
    Call Killoughs Shooting...
  10. Replies
    3
    Views
    468

    Without a picture it is tougher, I would go under...

    Without a picture it is tougher, I would go under the assumption if they are air rifle parts they are likely 11mm.
    As such a set of Kelblys will work if you mill off the sharp dovetail edge a bit...
  11. Replies
    8
    Views
    538

    Nice target.

    Nice target.
  12. Your money but it has long been shown, these days...

    Your money but it has long been shown, these days that is waaay too much gain. Guys going gain now find about an inch is max.
    In CF the gains go as little as 1/8" . You may or may not find a smith...
  13. Replies
    16
    Views
    1,645

    Concerned; I have one of these. I bought it...

    Concerned; I have one of these. I bought it for rimfire benchrest. It won't focus at 50 yards. Beyond 75 or so, its a great scope for the money. It is currently on a 6BR. I am pleased with...
  14. Replies
    18
    Views
    17,595

    Sticky: I think there is an Ohio venue, Most schedules...

    I think there is an Ohio venue, Most schedules are being finalized and gradually posted up on the site over coming weeks.
  15. This has been widely discussed/recognized. The...

    This has been widely discussed/recognized. The first shot(s) down a barrel, oiled or not is faster because properly distributed lube down a barrel from subsequent shots slow a slug down.
    Oil in a...
  16. Replies
    9
    Views
    936

    If you tend to follow him, you will notice he...

    If you tend to follow him, you will notice he will write something and a few months later contradict the previous tip.No doubt, plenty of good stuff but lots of head fakes as well.
    These days seems...
  17. Replies
    9
    Views
    936

    That there is/was a likely head fake which even...

    That there is/was a likely head fake which even he, likely, gave up on. In any event, it might pay to remember how long ago it was written.
    These days the choices seem to come down to two, learn to...
  18. Many, if not most, probably do finish with oil of...

    Many, if not most, probably do finish with oil of some type according to personal preference.
  19. Thread: Rimfire tuners

    by tim
    Replies
    22
    Views
    2,721

    If it's 1985. Any good ammo.....it's a complete...

    If it's 1985. Any good ammo.....it's a complete waste of time. If it's crap ammo, you have slightly less crappy ammo.
  20. Thread: Fudd tuner

    by tim
    Replies
    4
    Views
    768

    Don't think so.

    Don't think so.
  21. Thread: bullets

    by tim
    Replies
    9
    Views
    2,117

    IMHO, the absolute best are the ones that are...

    IMHO, the absolute best are the ones that are absolutely the most consistent, starting with great jackets. Consistent, weight, diameter with or without drive band, and base to ogive measurement.
    You...
  22. Replies
    52
    Views
    5,365

    So, apparently , is access to a keyboard.

    So, apparently , is access to a keyboard.
  23. Replies
    7
    Views
    1,365

    As stated you can find Mike Bush on forums, I...

    As stated you can find Mike Bush on forums, I have had conversations with him and he is certainly a sharp guy that seems to try and test everything as well as coming up with some pretty innovative...
  24. Replies
    5
    Views
    690

    JB used properly works, lots of guys use it...

    JB used properly works, lots of guys use it improperly and ruin barrels.....lots of barrels.
    get some SharpShootr No Lead, plug one end of a badly leaded barrel and fill it....let it stand over...
  25. Thread: Falcon actions!

    by tim
    Replies
    19
    Views
    3,873

    What exactly needs to be said that hasn't already...

    What exactly needs to be said that hasn't already been said, now it seems, verified by yourself.
    Check IR50/50 and PSL equipment lists as well if you like.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4