Tab Content
  • tim's Avatar
    01-21-2021, 08:49 PM
    tim replied to a thread Chamber Burrs in Gunsmiths Corner
    Well, there you go. Basically you made a hobb which some RF smiths have used to finish a RF chamber and it absolutely can be used to clean up a...
    10 replies | 1247 view(s)
  • tim's Avatar
    01-17-2021, 07:56 PM
    There must have been 4-5 well documented Wall Street Journal stories as well as lots of others, if not mistaken months later same stuff listed in the...
    37 replies | 2405 view(s)
  • tim's Avatar
    01-17-2021, 06:59 PM
    tim replied to a thread Ncswic in General Discussion
    W.....T.....F are you talking about? I mean, I realize itís winter in AK but CHRIST.
    4 replies | 682 view(s)
  • tim's Avatar
    01-17-2021, 06:09 PM
    Ollie North started to uncover how much $ was being spent on personal, non NRA stuff. Does Waynes wife really need a $5000 hair appointment ? Does he...
    37 replies | 2405 view(s)
  • tim's Avatar
    01-16-2021, 02:35 PM
    Damn right!
    37 replies | 2405 view(s)
  • tim's Avatar
    01-08-2021, 05:41 PM
    Kev, Always great to get your input and happy new year. I believe you are correct. I do not think the experiment lasted too long or was...
    21 replies | 1549 view(s)
  • tim's Avatar
    01-06-2021, 07:19 PM
    tim replied to a thread 25 Creedmoor in Centerfire Benchrest
    The fart in church has struck......again.
    10 replies | 1390 view(s)
  • tim's Avatar
    01-04-2021, 04:12 PM
    tim replied to a thread Winchester 52A in Rimfire Benchrest
    Bob, tongue in cheek since you should know the question you asked is impossible to get any credible answer. Guns history, proper cleaning, you have...
    3 replies | 596 view(s)
  • tim's Avatar
    01-04-2021, 12:28 PM
    tim replied to a thread Winchester 52A in Rimfire Benchrest
    .4125Ē on average
    3 replies | 596 view(s)
  • tim's Avatar
    01-01-2021, 02:26 PM
    tim replied to a thread Chamber Burrs in Gunsmiths Corner
    Butchy, pay attention. Happy New Year
    10 replies | 1247 view(s)
  • tim's Avatar
    12-31-2020, 06:59 PM
    tim replied to a thread Chamber Burrs in Gunsmiths Corner
    One of the absolute better ways to destroy the potential of a RF match chamber. To the OP, one of the many reasons the art of a 22 chamber...
    10 replies | 1247 view(s)
  • tim's Avatar
    12-31-2020, 05:33 PM
    It is, although have a ratchet as well.....strictly speaking not MI. Sorry, only shoot 50. 10X X3L in a Meredith TMBR.
    10 replies | 1269 view(s)
  • tim's Avatar
    12-31-2020, 01:01 PM
    Pedro, those blocks would be the traditional ones that I would assume as well but the one shown, once you wrap your head around it is very...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-31-2020, 12:53 PM
    OK. Itís hard to tell. May I assume it is inleted/glued from the bottom? I can see here where that assist in preventing wood movement in the stock...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-31-2020, 10:57 AM
    Is that actually a bedding block ? I would almost call them kind of hybrid pillars, large but separate. Asfar as this thread is concerned, is a...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-30-2020, 05:09 PM
    Well, there you go, I learned something today.....hadnít realized they would be bedded over , can see how that could be stock specific. The one I...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-30-2020, 03:23 PM
    Scott, you have me curious. I know Penrodís work is as good as it gets....what was the thinking on the bedding block? How did iT perform for you?...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-30-2020, 03:20 PM
    Unless the stock has really been hogged out you would be probably far ahead to have it bedded and pillared. Tom has done several RFís for me and a...
    21 replies | 1549 view(s)
  • tim's Avatar
    12-29-2020, 11:45 PM
    So....since youíre on a benchrest forum and few, if any BR builds use them, the question is what for ?
    21 replies | 1549 view(s)
  • tim's Avatar
    12-28-2020, 05:24 PM
    tim replied to a thread RCBS matchmaster in Centerfire Benchrest
    Thatís , I assume, why it was locked with that screw. When you unlocked it, that was supposed to be a one time procedure, to release the scale...
    7 replies | 992 view(s)
  • tim's Avatar
    12-28-2020, 01:59 PM
    tim replied to a thread RCBS matchmaster in Centerfire Benchrest
    Too big, too heavy, etc. Also, have been told but am not absolutely sure, you do not want to have these things on their sides.....it might...
    7 replies | 992 view(s)
  • tim's Avatar
    12-27-2020, 05:07 PM
    tim replied to a thread RCBS matchmaster in Centerfire Benchrest
    Yeah, I looked at variations of that but a nice wooden clamshell type deal would be nice, right? Some enterprising woodshop type guy can make a few...
    7 replies | 992 view(s)
  • tim's Avatar
    12-24-2020, 03:19 PM
    Yes, I did see that. I guess, maybe coming is not the same as currently in use. I guess the practical answer is that the old micro groove thinking...
    10 replies | 1269 view(s)
No More Results
About tim

Basic Information

About tim
Location:
upstate, N.Y.
Occupation:
financial consultant

Statistics


Total Posts
Total Posts
2,907
Posts Per Day
0.44
General Information
Last Activity
01-22-2021 09:57 PM
Join Date
02-07-2003

1 Friend

  1. Team Windsor Team Windsor is offline

    Ed Longo

    Team Windsor
Showing Friends 1 to 1 of 1