Register
Help
Remember Me?
Home
Forum
New Posts
FAQ
Calendar
Community
Albums
Member List
Forum Actions
Mark Forums Read
Quick Links
Today's Posts
View Site Leaders
Who's Online
Classifieds
What's New?
Advanced Search
Member List
brickeyee
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
brickeyee
Registered User
Find latest posts
Find latest started threads
Mini Statistics
Join Date
07-15-2005
Last Activity
12-07-2019
03:26 PM
Recent Visitors
The last 10 visitor(s) to this page were:
Dans40X
,
DT1
,
Gene Beggs
,
Gunner223
,
jimship
,
mwezell
,
Ricco1949
,
Richard
,
sdean
,
steveberg
This page has had
14,546
visits
Tab Content
brickeyee's Activity
About Me
Tab Content
All
brickeyee
Friends
Photos
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
12-07-2019,
03:26 PM
brickeyee
replied to a thread
tpi to M
in
Gunsmiths Corner
One of the things we used to do at one of my previous employers was use opponents equipment in testing US equipment. Everything from guns to radar...
see more
12 replies | 588 view(s)
12-06-2019,
05:44 PM
brickeyee
replied to a thread
tpi to M
in
Gunsmiths Corner
Cutting metric threads on a US pitched lathe has the same problem. You really need change gears in some different sizes than usual to pull it off. ...
see more
12 replies | 588 view(s)
12-06-2019,
03:51 PM
brickeyee
replied to a thread
Our New Lathe Arrived This Morning.
in
General Discussion
Years ago we had to install a larger vibration table. The older 1050s model (even with upgraded control and drive electronics) just could not...
see more
18 replies | 1625 view(s)
12-04-2019,
03:00 PM
brickeyee
replied to a thread
Thoughts men on scope for varmint rifle
in
General Discussion
4x to 6x is a little low for longer range varmints. I have it down to a lot of setup, one shot, one dead varmint. Maybe wait a few hours to see...
see more
34 replies | 2296 view(s)
12-03-2019,
02:09 PM
brickeyee
replied to a thread
Pumpkin turner mandrel
in
General Discussion
https://www.sinclairintl.com/reloading-equipment/case-preparation/neck-turning/turning-expander-mandrels/carbide-expander-mandrels-prod119668.aspx ...
see more
11 replies | 588 view(s)
12-02-2019,
01:51 PM
brickeyee
replied to a thread
Pumpkin turner mandrel
in
General Discussion
Sinclair https://www.sinclairintl.com/reloading-equipment/index.htm
see more
11 replies | 588 view(s)
12-01-2019,
06:11 PM
brickeyee
replied to a thread
Panda bolts
in
Gunsmiths Corner
I can still call them up, give them the serial number of my Panda action, and have a new barrel in a few weeks. I screw the barrel on and...
see more
4 replies | 949 view(s)
12-01-2019,
06:08 PM
brickeyee
replied to a thread
pumpkin pie
in
General Discussion
It is a huge amount of work, and they rarely come out all that much better than the Libby Canned Pumpkin. Even some of the cooking magazines give...
see more
5 replies | 458 view(s)
11-30-2019,
03:20 PM
brickeyee
replied to a thread
Thoughts men on scope for varmint rifle
in
General Discussion
And then you have to poke around the ITAR rules from the State Department. Most of our sporting scopes are not 'Defense Items.' But it takes a...
see more
34 replies | 2296 view(s)
11-23-2019,
03:30 PM
brickeyee
replied to a thread
Panda bolts
in
Gunsmiths Corner
Call up Kelbly's and see what they can do for you. Panda actions are easily altered and even a new bolt can be obtained.
see more
4 replies | 949 view(s)
11-23-2019,
03:28 PM
brickeyee
replied to a thread
Thoughts men on scope for varmint rifle
in
General Discussion
What varmints and ranges? Caliber? 6 mm makes for some really nice BC bullets for longer range critters. While for pure target use I avoid...
see more
34 replies | 2296 view(s)
11-23-2019,
03:16 PM
brickeyee
replied to a thread
Darn, my Neuvo Bolt Handle Broke.
in
General Discussion
I would have tended towards larger thread (lower TPI) in aluminum. Fine threads in aluminum are often not al that strong. 1/4-20 would likely...
see more
5 replies | 804 view(s)
11-15-2019,
04:04 PM
brickeyee
replied to a thread
Neck turning tool
in
General Discussion
A chamber casting in Cerrosafe is the way to determine neck diameter. The variation in the metals shrinkage and expansion after pouring and...
see more
15 replies | 1799 view(s)
11-12-2019,
04:32 PM
brickeyee
replied to a thread
Neck turning tool
in
General Discussion
And when neck tuning the final cut should not take off more than about 0.0005 in. It leaves a better finish.
see more
15 replies | 1799 view(s)
11-12-2019,
04:26 PM
brickeyee
replied to a thread
Neck turning tool
in
General Discussion
There are a couple of companies making neck thickness sorting tools using a dial indicator. Use a 'tenths indicator' (1/10,000 in graduations) for...
see more
15 replies | 1799 view(s)
11-12-2019,
04:05 PM
brickeyee
replied to a thread
Shooting Rest
in
General Discussion
The slingshot rest work very well.
see more
11 replies | 1675 view(s)
More Activity
No More Results
No Recent Activity
About brickeyee
Basic Information
Statistics
Total Posts
Total Posts
518
Posts Per Day
0.10
General Information
Last Activity
12-07-2019
03:26 PM
Join Date
07-15-2005