View Profile: Butch Lambert - Benchrest Central Forums

01-23-2020, 07:53 PM

geo.ulrich replied to a thread 7br? in General Discussion

As I said in post #2 I make them myself , well because I can and it really doesn't cost me anything but time. it was an experiment to see if it would...

23 replies | 750 view(s)

01-23-2020, 06:09 PM

geo.ulrich replied to a thread 7br? in General Discussion

well I guess they don't exist here's an 18 twist kreiger blank . what twist would you use for a .875 long 85/ 100 gr. bullet I have maybe 5-6 ...

23 replies | 750 view(s)

01-23-2020, 04:42 PM

Butch Lambert replied to a thread Chambering: indicate bore before threading and/or before reamer? in Gunsmiths Corner

I just saw a movie of it on a Haas TL-1 lathe. I'm not crazy about the way it indicates the barrel, Gordy method kinda?

99 replies | 17500 view(s)

01-23-2020, 03:21 PM

Butch Lambert replied to a thread Chambering: indicate bore before threading and/or before reamer? in Gunsmiths Corner

I see a 6 jaw chuck, what am I not seeing? How do you indicate your barrel or action?

99 replies | 17500 view(s)

01-23-2020, 10:13 AM

geo.ulrich replied to a thread 7br? in General Discussion

what twist barrel do you have? I used 16/17 for the short br bullets I think they were about .890 in length .

23 replies | 750 view(s)

01-22-2020, 05:28 PM

Butch Lambert replied to a thread Pre-Drill & Boring A Chamber in Gunsmiths Corner

Yes, I think it causes more problems. Why have a muzzle flopping around? Sure you can index it, but why? On the wandering bore, do you know that it...

42 replies | 1428 view(s)

01-22-2020, 04:21 PM

geo.ulrich replied to a thread 7br? in General Discussion

Its not the bullets its jackets we can make great bullets in any caliber. Of course if what you said is true we would still be shooting 22's in 222....

23 replies | 750 view(s)

01-22-2020, 02:07 PM

geo.ulrich replied to a thread 7br? in General Discussion

I have played with 7br with bullets in the 85-100 gr area it works great for score especially for 200 it doesn't drift near as much as the 30 br....

23 replies | 750 view(s)

01-21-2020, 04:09 PM

Butch Lambert replied to a thread Pre-Drill & Boring A Chamber in Gunsmiths Corner

Gene, let's start again. I use Deltronic pins to indicate muzzle and breach. I am in the headstock with a cathead on both ends. I do warm up my...

42 replies | 1428 view(s)

01-21-2020, 10:45 AM

Butch Lambert replied to a thread Pre-Drill & Boring A Chamber in Gunsmiths Corner

Gene, If I drill, indicate the throat, and bore to my indication at the throat, don't I have 2 points indicated?

42 replies | 1428 view(s)

01-20-2020, 11:33 AM

Butch Lambert replied to a thread Pre-Drill & Boring A Chamber in Gunsmiths Corner

Gene, I do it basically the same, but stick my 504-513 Mitutoyo in after drilling to make sure it didn't move while I was drilling. Can anybody...

42 replies | 1428 view(s)

01-19-2020, 12:45 PM

Butch Lambert replied to a thread Pillar to action mating surfaces in Gunsmiths Corner

Listen to Al as he has been around the farm and still hasn't fallen off the turnip truck.

44 replies | 1897 view(s)

01-19-2020, 12:36 PM

Butch Lambert replied to a thread Pencil Bluff, AR Spring Match in Competition Benchrest - ONLY!

Jay Lynn, Glenn Chism, My Grandson, Randy Conger, and I have stayed in Mt. Ida. It is a beautiful range with great people at the matches. One of my...

15 replies | 768 view(s)

01-19-2020, 08:03 AM

JerrySharrett replied to a thread Chambering: indicate bore before threading and/or before reamer? in Gunsmiths Corner

yep,they will move .

99 replies | 17500 view(s)

01-18-2020, 04:09 PM

Butch Lambert replied to a thread Fireform barrel idea in Gunsmiths Corner

My 30BR fireforming barrel is a 22CF barrel.

25 replies | 999 view(s)

01-16-2020, 11:43 AM

Butch Lambert replied to a thread Pillar to action mating surfaces in Gunsmiths Corner

Didn't know you got a Makita!

44 replies | 1897 view(s)

01-15-2020, 05:43 PM

geo.ulrich replied to a thread Pillar to action mating surfaces in Gunsmiths Corner

This works great other than I use epoxy resin with glass powder to make it into a putty....^^^^^^^^^ and a grommet on bottom for screws to pull...

44 replies | 1897 view(s)

01-13-2020, 06:05 PM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

them is the ones....

15 replies | 948 view(s)

01-13-2020, 05:31 PM

Butch Lambert replied to a thread Manny Garcia Has Passed in Competition Benchrest - ONLY!

He was a very fine man and will be truly missed.

22 replies | 1864 view(s)

01-13-2020, 05:27 PM

Butch Lambert replied to a thread Our New Lathe Arrived This Morning. in General Discussion

Louis, he is a pretty good guy, if I say so myself.

59 replies | 7691 view(s)

01-13-2020, 04:05 PM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

Al, again STRAIGHT FLUTE CARBIDE key seat cutters not helixed. actions are hard but not real bad just take it easy over the base holes thats where...

15 replies | 948 view(s)

01-13-2020, 02:26 PM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

Hence the reason for the 2 flute straight flute key seat cutters no felix less torquing

15 replies | 948 view(s)

01-13-2020, 10:16 AM

Butch Lambert replied to a thread How many have machined a flat on the bottom of a Rem action? in Gunsmiths Corner

Check mraps other posts.

13 replies | 990 view(s)

01-13-2020, 10:11 AM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

Funny they have been finishing slots with on size end mills for years. look at electric motor shafts or printing rolls ....unless it NEEDS to be...

15 replies | 948 view(s)

01-12-2020, 08:39 PM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

You could also clamp straight to table against pins and use a milling cutter on arbor at 90* try the straight flute cutters they are made in stub...

15 replies | 948 view(s)

01-12-2020, 08:17 PM

geo.ulrich replied to a thread Manny Garcia Has Passed in Competition Benchrest - ONLY!

Another loss to Bench Rest, he was one of the best the sport offered... R.I.P.

22 replies | 1864 view(s)

01-12-2020, 08:03 PM

geo.ulrich replied to a thread solid carbide 90°end mill, HOW?? in Gunsmiths Corner

Al, Rough slot first 3/16 then finish with a 1/4 I would go with straight flute carbide key seat cutters..what rpm are you running at

15 replies | 948 view(s)

01-06-2020, 05:29 PM

Dans40X replied to a thread remington actions in Gunsmiths Corner

Mram10 Registered User This message is hidden because Mram10 is on your ignore list. This is what you will see if you put someone on your IGNORE...

36 replies | 3831 view(s)

01-05-2020, 04:53 PM

Butch Lambert replied to a thread remington actions in Gunsmiths Corner

Dan, Al, We have been graced by mr mrap!

36 replies | 3831 view(s)

01-05-2020, 01:52 PM

Dans40X replied to a thread Disposing of Live Primers in General Discussion

Excavate a small hole in Mother Earth. Dump primers into hole w/ a small amount of accelerator. Ignite safely. When smoke subsides. Back fill...

69 replies | 4244 view(s)

Butch Lambert
Registered User

Mini Statistics

More 33 Friends

Rustystud

sgt_jamez

tropas nomadas

Law Dawg

eww1350

2RECON

Recent Visitors

Basic Information

About Butch Lambert

Contact

Statistics

Total Posts

General Information

33 Friends

2RECON

333smitty

Big Gunner

Big Man

Chad Schmidt

Charles E

cntryboy1289

cut rifled

Dans40X

Dave B

Butch Lambert Registered User

Mini Statistics

More 33 Friends

Recent Visitors

Basic Information

About Butch Lambert

Contact

Statistics

Total Posts

General Information

33 Friends

Butch Lambert
Registered User