Tab Content
  • WallyDog's Avatar
    04-07-2020, 09:47 AM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    Got the AcraGlas gel sooner than expected so the rear pillar got spooged in yesterday. 10 hr cure time. I was a lil light on how much I used but not...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    04-06-2020, 06:20 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    This old Mauser IS a fussy bed job. Im going to do the rear pillar first. Once that is done ill have a better shot at doing the recoil lug area and...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    04-06-2020, 12:36 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    I had a very similar gun to the one you mentioned. It was a M98 action on a huge Fagen mahogany stock. White line recoil pad and large Monte...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    04-05-2020, 12:20 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    Im new to this posting of pictures online but Ill give it the old quarantine try! These are pics of an assembled Mauser with Boyd stock pre bedding...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    04-04-2020, 03:43 PM
    Be Careful here! This man is Irish. As such he is certainly used to bouts of extreme misery from various shenaniagins that may be much different for...
    26 replies | 1757 view(s)
  • WallyDog's Avatar
    04-04-2020, 03:30 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    Received the Boyd stock in 10 days of ordering it! I am impressed to be honest. The quality is pretty good with the floorplate inletting being really...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    04-02-2020, 02:10 PM
    After watching the video and reading the comments Id say James has found a better way to make more accurate throats IN SCALE to larger number...
    52 replies | 3246 view(s)
  • WallyDog's Avatar
    03-26-2020, 08:27 PM
    Unconfirmed by CDC but...... rumor is Racing Gas fumes kills Covid 19. Just sayin Wally
    23 replies | 2291 view(s)
  • WallyDog's Avatar
    03-23-2020, 11:42 AM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    A dog point set screw has a dowel pin like on one end rather than a tapered point. Use it like a dowel pin with a drilled hole in your base material...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-22-2020, 10:07 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    I did a little bit. Right now its about .020 off the lands with the 130. I think its the stock or I just totally messed up that old HBR barrel when I...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-22-2020, 10:02 AM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    The bases are epoxied to the action but its a good idea to JB the bases and rings Id say. I have never physically seen the bases move. The groups are...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-22-2020, 07:35 AM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    In reality handloading the 7.65 x 53 is just as easy to exceed the 1891's intended loads as a 308 win would be. I did qualify the loads as 2600 fps...
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-21-2020, 06:39 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    Lets try again here:
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-21-2020, 06:14 PM
    WallyDog replied to a thread One Last Time in Gunsmiths Corner
    I'll try
    34 replies | 2581 view(s)
  • WallyDog's Avatar
    03-21-2020, 04:23 PM
    Broke out a 308 deer rifle I had recently chambered and shot maybe 20 rnds thru it before deer season. Again I had carbon on the lands and grooves...
    20 replies | 5778 view(s)
  • WallyDog's Avatar
    03-09-2020, 12:54 PM
    WallyDog replied to a thread Pillars in Gunsmiths Corner
    I started doing pillars shaped as a "T" in the side view. The larger 5/8 diameter is for the action to set on and doing a blind hole on the inside of...
    21 replies | 4232 view(s)
  • WallyDog's Avatar
    03-09-2020, 07:44 AM
    WallyDog replied to a thread Pillars in Gunsmiths Corner
    Accuracy in a jar! Got to try some just because of the Logo!
    21 replies | 4232 view(s)
No More Results
About WallyDog

Basic Information

Statistics


Total Posts
Total Posts
64
Posts Per Day
0.04
General Information
Last Activity
04-07-2020 09:47 AM
Join Date
05-22-2015